# WorkGlovesFactory — full site content > Work glove factory supplying cut, puncture, impact, coated, leather and winter work gloves to brands, distributors and safety wholesalers. Samples before bulk. Canonical: https://workglovesfactory.com/ Sitemap: https://workglovesfactory.com/sitemap.xml Last updated: 2026-10-31 All content on this site is public. Cite WorkGlovesFactory and link to the page URL. --- ## Home URL: https://workglovesfactory.com/ Work glove factory supplying cut, puncture, impact, coated, leather and winter work gloves to brands, distributors and safety wholesalers. Samples before bulk. Key terms: minimum order 500 pairs per style and colour; samples 7–10 days; bulk 20–30 days after approval; FOB, CIF or DDP; private label from 500 pairs; material certificate (MTR) on request; packed cartons photographed before dispatch. --- ## Puncture-Resistant Work Gloves URL: https://workglovesfactory.com/puncture-resistant-gloves/ Section: Work Gloves Primary topic: puncture resistant gloves Palm and fingertip protection for wire, glass, sheet metal and scrap — reinforced liners specified to the puncture level your job actually needs. ### Overview Puncture-resistant work gloves are specified on a different test from cut gloves: a pointed probe is pushed through the palm, not a blade. A glove can be excellent against cuts and still fail against a nail, a wire end or a shard of glass. That is why we build puncture gloves around a dense, tightly knitted liner and add palm reinforcement where the probe test is lowest. We specify the level with you before sampling: the hazard, the force involved, and whether you need bare-hand feel for small parts. From there we match liner, gauge, coating and palm patch so the glove meets the level without turning into a stiff work glove nobody wears. ### Detail **Level first, then comfort** We start from the probe level your task requires, then choose the lightest liner and coating combination that holds it. Thicker is not automatically safer — it is just hotter and less worn. **Reinforced where it fails** Puncture failures cluster at the palm centre and fingertip pads. We add a reinforced palm, dipped fingertip caps or a leather patch in those zones instead of thickening the whole glove. **Coating matched to the surface** Sandy nitrile for oily scrap, flat nitrile for dry metal, PU for small parts that need feel. The coating changes grip and abrasion life, not the puncture level of the liner underneath. ### Specification - Puncture level: ANSI/ISEA 105 level 3–5 (specified per style) - Liner: 13G / 15G HPPE + glass fiber, or polyester - Palm options: Sandy nitrile, flat nitrile, PU, leather patch - Cuff: Knit wrist or 22–26 cm knit cuff - Sizes: US 6–11, custom grading on request - MOQ: 500 pairs per style and color - Packaging: Polybag, header card, printed bag, 100–200 pairs per carton - Lead time: Samples 7–10 days · bulk 20–30 days after approval ### Puncture levels and where they fit Levels follow ANSI/ISEA 105. The right level is the lowest one that covers your hazard — higher levels cost feel. | Level | Probe force | Typical build | Where it is used | | --- | --- | --- | --- | | 1 | ≥ 10 N | Light PU-dipped knit | Packing, light assembly, dry cardboard | | 2 | ≥ 20 N | Coated knit with denser liner | Warehouse, general handling | | 3 | ≥ 60 N | HPPE blend + reinforced palm | Wire, sheet metal edges, recycling | | 4 | ≥ 100 N | HPPE + glass fiber, palm patch | Scrap handling, glass, demolition | | 5 | ≥ 150 N | Heavy liner + leather palm | Sharps, heavy scrap, demolition | ### Questions **Is puncture resistance the same as cut resistance?** No. Cut resistance uses a rotating blade; puncture resistance uses a pointed probe. A glove rated A5 for cut can still be level 1 for puncture. If your hazard is nails, wire ends or glass, specify puncture level separately. **Can these gloves stop hypodermic needles?** No work glove should be presented as needle-proof. Needle-resistant materials exist for specific controlled applications, but they are a different product class. Tell us the actual hazard and we will tell you honestly what a knitted glove can and cannot do. **Which palm do you recommend for oily scrap?** Sandy nitrile over an HPPE liner: the rough finish holds oily metal, and the liner carries the puncture level. For dry glass or sheet metal, a leather palm patch usually lasts longer than a dipped palm. **What is the minimum order and sampling process?** 500 pairs per style and color. We send a sample pair with the specified liner, coating and level for you to wear on the job before bulk. Bulk production starts only after you approve that sample. ### Related - Cut Resistant Gloves: https://workglovesfactory.com/cut-resistant-gloves/ - Impact Resistant Gloves: https://workglovesfactory.com/impact-resistant-gloves/ - Nitrile Coated Gloves: https://workglovesfactory.com/nitrile-coated-gloves/ - ANSI Cut Levels: https://workglovesfactory.com/guides/ansi-cut-levels/ --- ## PU Coated Work Gloves URL: https://workglovesfactory.com/pu-coated-gloves/ Section: Work Gloves Primary topic: pu coated gloves Thin, breathable palm-dipped gloves for small parts, assembly and packing — the lightest option in the range, and the one buyers reorder most. ### Overview PU coated work gloves are the dexterity choice. The coating sits thin on a fine-gauge liner, leaves the back of the hand open to air, and keeps enough friction to pick up a screw, a connector or a folded carton without pinching. For work where the hazard is abrasion and handling rather than cut or heat, PU is usually the right first sample. We run PU on 13-gauge polyester for durability and on 15-gauge nylon when feel matters more. Palm dip, three-quarter dip and full dip are all available, along with touchscreen fingertips and a knit wrist or short cuff. Washability is the other half of the cost equation. A PU glove can be laundered a limited number of times and reused, which changes the cost per shift more than the unit price does. Ask for a glove that still has a palm after washing; a coating that cracks at the knuckles after three cycles is the expensive option even at the lower price. ### Detail **Feel you can work in** A 15G nylon liner with a thin PU palm is close to bare-hand dexterity. It is the difference between a glove that gets worn for a full shift and one that ends up in a pocket. **Breathable back** Open-back construction lets heat out. In warm warehouses this matters more than another gram of coating thickness, because a sweaty glove comes off. **Dip length by task** Palm dip for dry handling, three-quarter dip for knuckle scuffs, full dip when the whole hand meets grit. We match the dip to the wear pattern you describe. ### Specification - Liner: 13G polyester or 15G nylon - Coating: Polyurethane, palm / 3/4 / full dip - Grip: Dry and light-oily handling - Cuff: Knit wrist, 2.5–3 cm - Sizes: US 6–11 - MOQ: 500 pairs per style and color - Packaging: 10 pairs per polybag, 200 pairs per carton - Lead time: Samples 7–10 days · bulk 20–30 days ### Gauge and dip selection A finer gauge gives more feel and less abrasion life. Choose by the wear you actually see. | Build | Feel | Abrasion life | Best for | | --- | --- | --- | --- | | 13G polyester, palm PU | Good | Standard | Packing, general assembly, logistics | | 15G nylon, palm PU | Highest | Lower | Electronics assembly, small parts | | 13G, 3/4 PU | Good | Higher | Handling with knuckle contact | | 13G, full PU | Fair | Highest | Wet-ish, gritty handling | ### Questions **PU or nitrile for assembly work?** PU when parts are dry and you need feel. Nitrile when there is oil, coolant or abrasion that eats a thin PU palm quickly. Many buyers stock both and issue them by workstation. **Do you offer touchscreen fingertips?** Yes. Conductive fingertips can be added to thumb and index, or to all five fingers. Confirm the device type when you order, because the conductive yarn is matched to capacitive screens. **Can the glove be washed and reused?** Palm-dipped PU gloves can be hand-washed in cool water and air-dried, which extends life in clean assembly. They are not intended for repeated industrial laundering. **What is the minimum order?** 500 pairs per style and color, in mixed sizes. Sample pairs are sent before bulk so you can check fit, feel and coating adhesion on your own line. ### Related - Nitrile Coated Gloves: https://workglovesfactory.com/nitrile-coated-gloves/ - Grip Work Gloves: https://workglovesfactory.com/grip-work-gloves/ - Warehouse Gloves: https://workglovesfactory.com/warehouse-gloves/ - Types of Work Gloves: https://workglovesfactory.com/guides/types-of-work-gloves/ --- ## Nitrile Coated Work Gloves URL: https://workglovesfactory.com/nitrile-coated-gloves/ Section: Work Gloves Primary topic: nitrile coated gloves The workhorse coating for oil, abrasion and wet-ish handling — sandy, foam or flat, on liners from light assembly to heavy scrap. ### Overview Nitrile coated work gloves earn their place where PU wears out: oily components, abrasive surfaces, coolant, and handling that scuffs the palm all shift. The coating is tougher than PU and resists oil, so grip does not disappear the moment a part comes out of a machine. Finish matters as much as the chemistry. Sandy nitrile gives the best wet and oily grip, foam is lighter and more breathable, and flat nitrile is the most abrasion-resistant but the least grippy when wet. We pick the finish from your surface, not from a catalogue page. Size grading matters more on a coated glove than on a leather one, because the liner is knitted to a specific hand length. A glove one size too long bunches at the fingertips, and that slack fabric is the first thing to wear through. Send the size split you issue today and we will match the grading instead of shipping a flat carton. ### Detail **Oil stays on the part** Nitrile resists oils and greases, so the glove keeps its grip instead of becoming slick. That is why it is the default for machined parts, maintenance and automotive handling. **Three finishes, three jobs** Sandy for wet and oily, foam for dry abrasive handling with more breathability, flat for maximum abrasion life. We sample the finish that matches your wear pattern. **Liner carries the protection** The same nitrile dip can sit on a 13G polyester liner for general handling or an HPPE blend for cut protection. The coating does not limit the cut level you can specify. ### Specification - Liner: 13G / 15G / 18G polyester, nylon or HPPE blend - Coating: Sandy, foam or flat nitrile; palm or full dip - Cut options: ANSI A1–A4 depending on liner - Cuff: Knit wrist or 22 cm safety cuff - Sizes: US 6–11 - MOQ: 500 pairs per style and color - Packaging: 12 pairs per polybag, 120–240 pairs per carton - Lead time: Samples 7–10 days · bulk 20–30 days ### Which nitrile finish Sandy is the default for oily and wet parts. Foam balances grip and breathability on dry abrasive work, while flat nitrile is kept for heavy abrasion where wet grip is not the priority. | Finish | Grip when wet | Abrasion | Breathability | Typical use | | --- | --- | --- | --- | --- | | Sandy | Best | High | Medium | Oily parts, outdoor, wet handling | | Foam | Good | Medium | High | Dry abrasive handling, assembly | | Flat | Fair | Highest | Low | Heavy abrasion, dry surfaces | ### Questions **What is the difference between nitrile-coated and disposable nitrile?** A coated glove is a knitted liner with a nitrile palm, made to be worn and reused for handling work. A disposable nitrile glove is a single-use barrier film. They solve different problems and are priced differently. **Will nitrile protect against chemicals?** A coated work glove is not a chemical barrier. For splash and permeation protection you need a dedicated chemical glove with published breakthrough data for the specific substance. Tell us the chemical and we will say whether we can help. **Can I get cut protection with a nitrile palm?** Yes. Nitrile is applied over HPPE or glass-fiber liners to reach ANSI A2–A4. The cut level follows the liner, so specify both the level and the finish. **Do you supply private-label packaging?** Yes. Printed polybags, header cards, hang tags and carton marks can all carry your brand. Artwork is confirmed before production, and a pre-production sample is sent for approval. ### Related - PU Coated Gloves: https://workglovesfactory.com/pu-coated-gloves/ - Cut Resistant Gloves: https://workglovesfactory.com/cut-resistant-gloves/ - Grip Work Gloves: https://workglovesfactory.com/grip-work-gloves/ - Disposable Nitrile Gloves: https://workglovesfactory.com/disposable-nitrile-gloves/ --- ## Custom Work Gloves, Made to Your Spec URL: https://workglovesfactory.com/custom-work-gloves/ Section: Custom Manufacturing Primary topic: custom work gloves Your liner, your coating, your colors, your packaging — built to a sample you approve, from 500 pairs per style. ### Overview Most custom work glove buyers do not need a new glove from scratch. They need their own version of a proven construction: a specific liner and gauge, a coating finish they already know works, their brand on the back and their packaging on the shelf. That is what we build. The process is deliberately plain. You send the spec or a sample of the glove you use today. We match materials, make a counter-sample, and send it with the packaging mock-up. Nothing goes to bulk until that sample is approved in writing. A written spec sheet is the part that usually gets skipped and is usually the reason a reorder drifts. Ours records liner, gauge, coating, finish, size grading, colour reference, logo placement and packing count. That sheet is what the second order is made against, so a change in yarn or construction shows up as a question rather than as a surprise in your warehouse. ### Detail **Start from what works** Send a glove you already use, or describe the liner, coating and level. We match it, then improve the weak point — usually palm wear, cuff length or sizing consistency. **Brand on the glove** Logo print on the back of the hand, woven or printed label, custom knit color and contrast cuff. We confirm artwork and placement on the sample, not after production. **Packaging for your channel** Polybag, printed bag, header card, hang tag, size sticker and carton mark. Retail-ready or plain bulk cartons — both are set up from the same approved sample. ### Specification - Customization: Liner, gauge, coating, color, logo, packaging - MOQ: 500 pairs per style and color - Sampling: Counter-sample in 7–10 days - Bulk lead time: 20–30 days after sample approval - Materials: PVC, nylon, nitrile, NBR, latex, cowhide, goatskin, pigskin, cotton, cotton yarn, canvas, HPPE, glass fiber, steel - Sizes: XS–2XL (US 6–11), custom grading - Length: 10–33 cm cuff or overall, family dependent - Incoterms: FOB, CIF, DDP - Payment: 30% deposit, balance before shipment - Artwork: AI, PDF or high-resolution PNG ### What can be customized Most private-label orders change the liner, coating, colour, branding and packing, not the basic pattern. Each element is confirmed on a counter-sample or a physical proof before bulk. | Element | Options | Confirmed on | | --- | --- | --- | | Liner | Polyester, nylon, HPPE, cotton, leather | Counter-sample | | Coating | PU, nitrile (sandy/foam/flat), PVC, latex-free options | Counter-sample | | Color | Knit color, coating color, cuff color | Color swatch + sample | | Branding | Back-of-hand print, woven label, size print | Artwork proof + sample | | Packaging | Polybag, printed bag, header card, hang tag, carton | Packaging mock-up | ### Specification options by parameter Medical, firefighting, chemical-barrier and electrical-insulating gloves are outside this range. | Parameter | Range we build | Confirmed on | | --- | --- | --- | | Material | PVC, nylon, nitrile, NBR, latex, cowhide, goatskin, pigskin, cotton, cotton yarn, canvas, HPPE, glass fiber, steel | Counter-sample | | Size | XS–2XL (US 6–11); one size on selected cotton styles | Size grading sheet | | Length | 10 cm to 33 cm cuff or overall, family dependent | Measurement drawing | | Function | Grip, abrasion, oil, cut, puncture, breathability, dust, ESD | Approved spec and sample | | Application | General industry, construction, logistics, automotive, agriculture, metalworking, food handling, electronics | Use description | ### Questions **Can you match a glove we already buy?** Usually yes. Send one pair and the spec if you have it. We identify liner, gauge, coating and cuff, then send a counter-sample so you can compare side by side before committing. **What is the real minimum order?** 500 pairs per style and color. Mixed sizes are fine within that quantity. If you need several colors, each color carries its own 500-pair minimum. **How long does a custom program take?** Counter-sample in 7–10 days, then 20–30 days for bulk after you approve it. Packaging artwork is approved in parallel, so it does not add a separate stage. **Can you hold inventory for repeat orders?** We can plan repeat production against a forecast and hold finished cartons for scheduled release. Terms depend on volume and seasonality; tell us your reorder pattern and we will propose a schedule. **Can you confirm sizes and lengths before bulk?** Yes. The approved spec sheet records size grading, cuff or overall length and the measurement point, along with material, coating and packing. The counter-sample is measured against that sheet, so a reorder is made to the same numbers. ### Related - Wholesale Work Gloves: https://workglovesfactory.com/wholesale-work-gloves/ - Work Glove Manufacturer: https://workglovesfactory.com/work-glove-manufacturer/ - Custom Packaging: https://workglovesfactory.com/contact/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## Impact-Resistant Work Gloves URL: https://workglovesfactory.com/impact-resistant-gloves/ Section: Work Gloves Primary topic: impact gloves TPR armor across the knuckles and fingers for struck-hand injuries, without turning the palm into a brick. ### Overview Impact-resistant work gloves target the back of the hand: knuckles against a beam, fingers caught between a pipe and a flange. A cut-resistant liner does nothing for that. The fix is a molded TPR (thermoplastic rubber) guard stitched over the knuckles and finger backs, shaped so it deflects rather than concentrates the hit. The design tension is real. More coverage protects more, but it also traps heat and reduces finger bend. We build impact gloves in three coverage levels and pair them with palm options from thin PU to sandy nitrile, so the glove still works for the task that caused the hazard. ### Detail **Coverage where hits land** Knuckle bridge plus finger segments, with an optional thumb guard. We shape the TPR to the liner so it stays put when the hand flexes instead of riding up. **Palm still works** Impact protection is only useful if the glove can hold the tool. Palm options run from thin PU for control to sandy nitrile for oily steel, with a reinforced thumb crotch on heavy builds. **Cut level on the same glove** Pair the TPR shell with an A3–A5 HPPE liner when the job also involves sharp edges. One glove, two hazards, instead of layering two pairs. ### Specification - Impact rating: ANSI/ISEA 138 level 1–3 (specified per style) - Back protection: Molded TPR knuckle and finger guards - Palm: PU, sandy nitrile or synthetic leather - Cut options: ANSI A2–A5 with HPPE liner - Cuff: Knit wrist or hook-and-loop - Sizes: US 7–11 - MOQ: 500 pairs per style and color - Lead time: Samples 7–10 days · bulk 20–30 days ### Impact levels and coverage Higher levels add protection and weight. Match the level to the struck-hand risk, not to the heaviest option available. | Level | Coverage | Typical build | Where it fits | | --- | --- | --- | --- | | 1 | Knuckle bridge | Light TPR on knit liner | Maintenance, light assembly | | 2 | Knuckle + finger backs | Segmented TPR, reinforced palm | Construction, rigging, HVAC | | 3 | Full back + thumb | Heavy TPR, leather or nitrile palm | Heavy steel, demolition, oil and gas | ### Questions **Do impact gloves also protect against cuts?** Only if the liner is cut-rated. The TPR shell handles impact; the liner handles cuts. Specify both — an A4 liner under a level 2 TPR shell is a common construction combination. **Will the TPR make my hands too hot?** It adds coverage, so it traps some heat. We use vented TPR segments and open-back liners on warm-weather styles, and can quote a lighter level 1 shell if heat is the deciding issue. **Can the glove be used for touchscreen work?** Yes, conductive fingertips can be added to thumb and index. On heavy TPR builds the fingertip pad stays thin, so the touch function still works. **What is the MOQ for a private-label impact glove?** 500 pairs per style and color. The TPR mold is shared across our standard shapes; a fully custom mold carries a separate tooling cost and longer lead time. For a repeat programme, that tooling is usually absorbed on the first reorder. ### Related - Cut Resistant Gloves: https://workglovesfactory.com/cut-resistant-gloves/ - Construction Gloves: https://workglovesfactory.com/construction-gloves/ - Anti-Vibration Gloves: https://workglovesfactory.com/anti-vibration-gloves/ - Mechanic Gloves: https://workglovesfactory.com/mechanic-gloves/ --- ## Work Gloves, Chosen by the Hazard URL: https://workglovesfactory.com/work-gloves/ Section: Work Gloves Primary topic: work gloves Seventeen glove families, one selection logic: start from the hazard, then choose liner, coating and level. Samples from 500 pairs per style. ### Overview Buyers usually arrive with a category name — cut gloves, nitrile gloves, winter gloves — but work gloves that perform are decided by three things: what the hand touches, what can hit it, and what the environment does to grip. A glove chosen by name alone is how crews end up with a drawer full of the wrong pair. This hub sorts the range by hazard rather than by catalogue order. Each family page states the liner, coating, protection level and the task it was built for, so you can shortlist two or three styles and sample them against each other. ### Detail **Start with the hazard** Cut, puncture, impact, abrasion, heat, cold or chemical splash. Name the dominant hazard and the shortlist narrows to two or three families immediately. **Then the environment** Dry, oily, wet or gritty changes the coating. Sandy nitrile for oil, PU for dry feel, PVC for rough wet work, leather for heat and abrasion. **Then the level** Specify ANSI/ISEA levels for cut, puncture and impact so the glove is neither under-protective nor heavier than the job requires. ### Specification - Families: 17 constructions across coated, leather, impact and insulated gloves - Coatings: PU, nitrile (sandy/foam/flat), PVC, foam latex - Liners: Polyester, nylon, HPPE, steel, cotton, cotton yarn, canvas, leather - Cut levels: ANSI A1–A6 - Sizes: XS–2XL (US 6–11); one size on selected cotton styles - MOQ: 500 pairs per style and color - Branding: Private label, logo print, custom packaging - Lead time: Samples 7–10 days · bulk 20–30 days ### Glove families at a glance Use this as a shortlist, then confirm the level and finish on a sample. | Family | Main hazard | Typical build | Often bought by | | --- | --- | --- | --- | | Cut resistant | Sharp edges | HPPE / glass fiber, PU or nitrile palm | Metal, glass, recycling | | Puncture resistant | Sharps, wire | Dense liner + reinforced palm | Scrap, demolition, waste | | Impact resistant | Struck hand | TPR back + nitrile or leather palm | Construction, rigging | | PU coated | Abrasion, small parts | 13G/15G knit + PU palm | Assembly, packing | | Nitrile coated | Oil, abrasion | Knit + sandy/foam nitrile | Machining, maintenance | | Leather | Abrasion, heat, sparks | Split cowhide or goatskin | Welding, rigging, masonry | | Winter | Cold | Fleece or acrylic lining + nitrile palm | Outdoor, cold storage | | Hi-visibility | Visibility | Fluorescent knit + reflective trim | Road, rail, site | ### Factory range by category Category names buyers use, mapped to the build and the page that specifies it. Sleeves and specialty builds are quoted with the glove order. | Category | Build | Where it is specified | | --- | --- | --- | | Coated cut-resistant gloves | HPPE or glass-fiber liner, PU or nitrile palm, A2–A5 | Cut resistant gloves | | Mechanical gloves | Knit liner, TPR back, nitrile or synthetic leather palm | Impact resistant / Mechanic gloves | | Steel and wire cut-resistant gloves | HPPE plus steel yarn, A5–A6, reinforced palm | Cut resistant gloves | | Welding gloves | Split cowhide or goatskin, 14 in gauntlet, aramid thread | Welding gloves | | Cut-resistant arm sleeves | HPPE knit tube, 18 in or 24 in, thumb slot optional | Quoted with cut glove orders | | ESD and anti-static gloves | Carbon or PU-coated knit, surface resistance stated per style | ESD and anti-static gloves | | Leather-patch cut gloves | HPPE liner with cowhide palm patch, A3–A5 | Cut resistant gloves | | Nylon gloves | 13G or 15G nylon liner, PU or nitrile palm | PU coated / Nitrile coated | | General-purpose / labor protection gloves | Jersey, cotton, PU coated or PVC dotted; no single rated level | Jersey and cotton / PU coated | | Non-slip gloves | PVC dots, sandy nitrile or crinkle finish | Grip work gloves | | Animal handling gloves | Cut-resistant liner with leather palm; not bite-rated | Cut resistant / Leather gloves | | Acid and chemical splash | Not a barrier glove; needs EN374 breakthrough data for the substance | Outside this range | | Electrical insulating gloves | Not offered; needs ASTM D120 or IEC 60903 class and test date | Outside this range | | Coated gloves | PU, nitrile, PVC or foam latex, palm, 3/4 or full dip | PU / Nitrile / PVC coated | | Cotton yarn gloves | 7 oz or 8 oz cotton jersey, knit wrist, dots optional | Jersey and cotton gloves | | Cotton cloth gloves | 8 oz cotton cloth, clute cut, band top | Jersey and cotton gloves | | Canvas gloves | Cotton canvas, clute cut, knit wrist | Jersey and cotton gloves | | Leather gloves | Split cowhide, goatskin, grain pigskin or grain cowhide | Leather work gloves | | Fire-service style gauntlets | Heavy split cowhide, 14 in gauntlet — general work glove, not NFPA 1971 PPE | Welding / Leather gloves | ### Sizes, lengths and materials Standard ranges shown; every value is confirmed on the approved sample before bulk. | Parameter | Range | Notes | | --- | --- | --- | | Materials | PVC, nylon, nitrile, nitrile rubber (NBR), latex, cowhide, goatskin, pigskin, cotton, cotton yarn, canvas, HPPE, glass fiber, steel | Blend and gauge selected for the hazard | | Sizes | XS–2XL (US 6–11); one size for selected cotton and PVC-dot styles | Custom grading from 500 pairs per style | | Cuff and overall length | 10 cm to 33 cm depending on family | 18–27 cm most common; 30–35 cm gauntlet | | Functions | Grip, abrasion, oil resistance, cut, puncture, breathability, dust, ESD | Protection level stated per approved spec | | Product types | General purpose, non-slip, cut-resistant, coated, leather, cotton | Mixed families can ship on one order | ### Applications by sector Where a hazard needs a different product class, the row says so. We do not stretch a work glove into a claim it cannot support. | Sector | Typical task | Family to start with | | --- | --- | --- | | General industry / industrial park | Maintenance, assembly, light handling | PU or nitrile coated | | Construction | Rebar, masonry, struck hand | Impact plus cut resistant | | Logistics and warehousing | Packing, picking, cutter opening | PU coated, touchscreen fingertips | | Automotive repair | Tools, parts, oil | Mechanic or impact, nitrile palm | | Agriculture and forestry | Fencing, pruning, outdoor handling | Leather, jersey or PVC dotted | | Machinery and metal fabrication | Sheet metal, plate, edges | Cut resistant A3–A5 | | Welding and metal joining | Stick, MIG, TIG | Leather gauntlet or TIG glove | | Oil, gas and mining | Pipe, tools, abrasive rock | Nitrile coated or impact; not a chemical barrier | | Electronics assembly | Components, boards, static-sensitive parts | ESD and anti-static | | Food processing | Food contact, wet cleaning | Food-contact disposable nitrile; coated glove for handling | | Steel and glass | Plate, sheet, sharp edges, heat | Cut A4–A6; heat resistant where hot | | Electrical manufacturing | Assembly and wiring | ESD or general work glove; not insulating PPE | | Power generation and utilities | Maintenance, wiring, substation work | General work glove; not insulating PPE | | Steel mill and foundry | Hot ingots, slag, furnace work | Heat resistant and leather; molten metal needs dedicated PPE | | Cleanroom, laboratory, semiconductor, photovoltaic | Low-lint handling in ESD areas | ESD and anti-static; not sterile or cleanroom-certified | | Electroplating and chemical handling | Plating baths, solvents | Outside this range for permeation; ask for a dedicated chemical glove | | Gardening, home, pets and outdoor leisure | Yard, cleaning, pets, travel | Jersey, PVC dotted or disposable nitrile | | Cold storage and outdoor winter work | Cold, wet, wind | Winter work gloves | | Fire rescue and forest fire | Fireground and wildfire | Outside this range as PPE; heavy leather work gauntlets are not NFPA 1971 rated | | Medical and clinical | Examination, patient care | Outside this range; our nitrile is industrial and food-contact grade | ### Questions **How do I choose between PU, nitrile and PVC coatings?** PU for dry handling and feel, nitrile for oil and abrasion, PVC for rough wet work and heavier abrasion. If you are unsure, send the task description and a photo of the surface and we will recommend two options to sample. **Do you sell to distributors as well as brands?** Yes. Distributors usually buy mixed pallets across several families; brands usually private-label two or three styles. Both start at 500 pairs per style and color. **Can I order mixed sizes in one carton?** Yes. Sizes are packed to your ratio, typically S–XXL. Tell us the ratio you sell and we will set the carton configuration before production. **What is the sample process?** We send the closest standard sample first, free of charge for evaluation, with freight at cost. If you need a modified build, a counter-sample follows in 7–10 days. **What sizes and cuff lengths can you produce?** XS–2XL, which is US 6–11, as standard, plus one-size builds for selected cotton and PVC-dot styles. Cuff and overall lengths run from 10 cm to 33 cm depending on the family: 22–24 cm is the common knit or safety cuff and 30–35 cm is the gauntlet range. Custom grading starts at 500 pairs per style. **Do you supply fire, medical or chemical-protective gloves?** No, not as rated PPE. Our nitrile is industrial and food-contact grade, not examination grade; our leather gauntlets are general work gloves, not NFPA 1971 firefighting PPE; and a coated work glove is not a chemical barrier. Tell us the hazard and we will say whether it is in range or needs a dedicated product class. **What are general-purpose work gloves?** The term covers light handling gloves — cotton jersey, PVC dotted, thin PU coated — bought by the bale for tasks with no single dominant hazard. If the job carries a rated hazard such as cut, puncture or heat, specify the level instead of the category name; the tables above map both naming systems. **Do you supply acid-resistant or electrical gloves?** No. Acid and chemical permeation protection needs a dedicated glove with EN374 breakthrough data for the specific substance, and electrical work needs ASTM D120 or IEC 60903 insulating gloves with a known test date. Our coated and nitrile work gloves are neither barriers nor insulators. Tell us the chemical, concentration and temperature, and we will say plainly whether a work glove is appropriate. ### Related - Safety Gloves: https://workglovesfactory.com/safety-gloves/ - Custom Work Gloves: https://workglovesfactory.com/custom-work-gloves/ - Wholesale Work Gloves: https://workglovesfactory.com/wholesale-work-gloves/ - Types of Work Gloves: https://workglovesfactory.com/guides/types-of-work-gloves/ - Jersey & Cotton Gloves: https://workglovesfactory.com/jersey-cotton-work-gloves/ - ESD & Anti-Static: https://workglovesfactory.com/esd-anti-static-gloves/ --- ## Cut-Resistant Work Gloves URL: https://workglovesfactory.com/cut-resistant-gloves/ Section: Work Gloves Primary topic: cut resistant gloves HPPE, glass-fiber and steel blends engineered to a cut level you specify — with the palm that keeps the glove on the hand all shift. ### Overview Cut-resistant work gloves get their rating from the liner, not the coating. HPPE (ultra-high-molecular-weight polyethylene) gives the best strength-to-weight ratio, glass fiber adds cut resistance at low cost, and steel or basalt yarns push the top levels. The blend and the gauge decide both the level and how the glove feels. We quote cut gloves by level first: A2 for light handling, A4 for general sheet metal, A5–A6 for heavy plate and glass. Then we match the palm to the environment — PU for dry feel, nitrile for oil, leather for hot and abrasive surfaces. ### Detail **The level you ask for** We build to the ANSI level, not to a marketing claim. Tell us the level and the task; we propose the liner blend and gauge that reach it without over-building the glove. **Gauge controls feel** 13-gauge is durable and comfortable for general handling; 15-gauge and 18-gauge give more dexterity for small parts at the same level. Finer gauge costs more and wears faster. **Palm matched to the surface** PU for dry precision, sandy nitrile for oily steel, leather for hot plate and rough abrasion. The palm changes grip life, not the cut level. ### Specification - Cut levels: ANSI/ISEA 105 A2–A6 (EN388 equivalent on request) - Liner: HPPE, HPPE + glass fiber, HPPE + stainless-steel composite yarn, steel blend - Gauges: 13G, 15G, 18G - Palm: PU, black sandy nitrile, foam nitrile, leather - Build variants: PU or nitrile coated, steel blend, yarn knit, leather patch, arm sleeves - Cuff: Knit wrist, 18–26 cm safety cuff - Sizes: XS–2XL (US 6–11) - Measured build: 25 cm length at size 9; 25.5 cm at size 10; palm width 10–11 cm; cuff width 9 cm - Sleeves: HPPE knit, 18 in or 24 in, thumb slot optional - MOQ: 500 pairs per style and color - Lead time: Samples 7–10 days · bulk 20–30 days ### Cut level quick reference Full A1–A9 chart with EN388 cross-reference: see the ANSI cut levels guide. | ANSI level | Test load | Typical task | Build | | --- | --- | --- | --- | | A1 | 200 g | Light assembly, packing | Polyester / light HPPE | | A2 | 500 g | General handling, warehouse | HPPE blend, 13G/15G | | A3 | 1,000 g | Sheet metal, glass handling | HPPE + glass fiber | | A4 | 1,500 g | Metal fabrication, recycling | HPPE + glass, 13G | | A5 | 2,200 g | Heavy plate, demolition | HPPE + steel, reinforced palm | | A6 | 3,000 g | Sharps, heavy scrap | Dense HPPE + steel, leather palm | ### Cut glove build variants The liner sets the cut level; the coating or patch sets grip, heat and abrasion. Sleeve levels are stated per style. | Variant | Build | Typical level | Best for | | --- | --- | --- | --- | | Coated cut, PU | HPPE or glass-fiber knit, PU palm | A2–A4 | Dry assembly, glass, light sheet metal | | Coated cut, nitrile | HPPE knit, sandy or foam nitrile palm | A2–A5 | Oily steel, recycling, maintenance | | Steel and wire blend | HPPE plus steel yarn, reinforced palm | A5–A6 | Heavy plate, scrap, demolition | | HPPE and stainless-steel | HPPE/stainless composite yarn, black sandy nitrile palm | Stated per style | Glass, wood, steel sorting, garden pruning | | Yarn knit, uncoated | HPPE or glass-fiber knit, knit wrist | A2–A4 | Dry handling in warm environments | | Leather-patch cut | HPPE liner with cowhide palm | A3–A5 | Hot, rough or abrasive plate | | Cut-resistant sleeve | HPPE knit tube, 18 in or 24 in | Stated per style | Forearm protection worn with a glove | ### Questions **HPPE or Kevlar for cut resistance?** HPPE gives higher cut levels at lower weight and is the default for most handling gloves. Aramid (Kevlar-type) fibers add heat resistance and are used where sparks or hot surfaces are also present. **Can cut-resistant gloves be washed?** Yes, most HPPE and coated styles can be machine-washed cold and air-dried. Avoid bleach and high heat, which degrade the fibers. Washing extends life but does not restore a worn liner. **Does a higher cut level always mean a better glove?** No. Higher levels usually mean a denser, warmer, stiffer glove. Specify the lowest level that covers the hazard — that is the glove crews will actually keep on. **Do you provide the level on the glove?** The level is stated on the approved spec sheet and can be printed on the glove or label as part of your private-label build. Confirm the marking requirement with your order. **Do you supply cut-resistant sleeves?** Yes, as an add-on to cut glove orders: HPPE knit sleeves in 18 in and 24 in, with elastic ends and an optional thumb slot. The cut level is stated per sleeve style. Tell us the forearm length and whether the sleeve sits under or over the glove cuff. **Can cut-resistant gloves be used for animal handling?** For cages, wire and sharp edges, yes — an HPPE liner or leather palm helps. They are not bite-rated: teeth load the liner differently from a blade, and no knitted work glove should be sold as bite-proof. Tell us the animal and the handling task and we will quote a cut level and palm that fit, with the limits stated. ### Related - ANSI Cut Levels A1–A9: https://workglovesfactory.com/guides/ansi-cut-levels/ - Puncture Resistant Gloves: https://workglovesfactory.com/puncture-resistant-gloves/ - Impact Resistant Gloves: https://workglovesfactory.com/impact-resistant-gloves/ - Construction Gloves: https://workglovesfactory.com/construction-gloves/ --- ## Safety Gloves, Specified by Standard URL: https://workglovesfactory.com/safety-gloves/ Section: Safety Gloves Primary topic: safety gloves If you buy against a standard, start here: hazard, then the rating, then the glove family that carries it. ### Overview Safety gloves are not bought by color or cuff style. Buyers start with a risk assessment, which names the hazard and the required protection level, and then look for gloves that carry that level with documented ratings. This hub is organized the same way. Every family page states which standard applies, what the levels mean, and where a knitted glove stops being the right answer. Where a hazard needs a different product class — chemical permeation, electrical insulation, structural firefighting — we say so instead of stretching a work glove into a claim it cannot support. ### Detail **Standard first** ANSI/ISEA 105 for cut, puncture and abrasion; ANSI/ISEA 138 for impact; EN388 as the European equivalent. We state the applicable standard per family. **Honest boundaries** A coated work glove is not a chemical barrier, an insulator or a firefighting glove. We tell you when the hazard needs a different product class rather than overselling a knit. **Documented on the sample** The approved sample and spec sheet carry the level, liner, coating and size grading, so your purchasing team orders against a fixed reference. ### Specification - Standards referenced: ANSI/ISEA 105, ANSI/ISEA 138, EN388 - Protection types: Cut, puncture, impact, abrasion, heat, cold, visibility - Cut range: ANSI A1–A6 - Impact range: ANSI/ISEA 138 level 1–3 - Sizes: US 6–11 - MOQ: 500 pairs per style and color - Private label: Logo, label, packaging - Lead time: Samples 7–10 days · bulk 20–30 days ### Hazard to standard to glove family Chemical permeation, electrical insulation and firefighting require dedicated products outside this range. | Hazard | Standard | Family to start with | | --- | --- | --- | | Sharp edges | ANSI/ISEA 105 cut | Cut resistant gloves | | Puncture / sharps | ANSI/ISEA 105 puncture | Puncture resistant gloves | | Struck hand | ANSI/ISEA 138 | Impact resistant gloves | | Abrasion | ANSI/ISEA 105 abrasion | PU or nitrile coated | | Contact heat | EN407 / ANSI heat | Heat resistant or welding | | Cold | EN511 | Winter work gloves | | Low light / traffic | ANSI/ISEA 107 colors | Hi-visibility gloves | | Chemical splash | EN374 (different product class) | Not a knit glove — ask us | ### Questions **What documentation comes with an order?** Every order ships against an approved spec sheet that states liner, coating, level and size grading, plus photos of the packed cartons before dispatch. If your risk assessment requires a third-party document, tell us before the order — we will say plainly whether it is in scope. **Which standard applies to cut-resistant gloves?** ANSI/ISEA 105 in the US and EN388 in Europe. The two tests are not directly interchangeable, so specify the market and we will quote the corresponding rating. **Can one glove cover cut and impact?** Yes. An HPPE liner provides the cut level and a TPR shell provides impact protection. Combining them avoids wearing two pairs, which is the usual reason compliance falls off. **Do you help with the risk assessment?** We can describe the protection a style provides and its limits. The formal assessment stays with your safety team; we make sure the glove specification is precise enough to be assessed. **What are mechanical gloves?** A buyer term for gloves that protect against mechanical risks — abrasion, cut, tear and puncture — rather than heat, chemicals or electricity. In the US the levels come from ANSI/ISEA 105, with impact from ANSI/ISEA 138; EN388 covers the same risks in Europe. In this range that means coated knit, leather and impact builds: the rating decides the glove, not the category name. ### Related - Work Gloves: https://workglovesfactory.com/work-gloves/ - ANSI Cut Levels: https://workglovesfactory.com/guides/ansi-cut-levels/ - Hi-Visibility Gloves: https://workglovesfactory.com/high-visibility-work-gloves/ - Glove Size Chart: https://workglovesfactory.com/guides/glove-size-chart/ --- ## Leather Work Gloves URL: https://workglovesfactory.com/leather-work-gloves/ Section: Work Gloves Primary topic: leather work gloves Split cowhide, goatskin and grain leather for heat, abrasion and grip that coated knits cannot survive. ### Overview Leather work gloves remain the right answer where the surface is hot, rough or grabby. Split cowhide takes abrasion and sparks, goatskin gives the best feel-to-durability ratio, and grain pigskin stays soft after repeated wet-dry cycles. The cut and the seam placement matter as much as the hide. We build Gunn cut and clute cut patterns with keystone or wing thumbs, welted seams in high-wear areas and optional palm patches. Cuffs range from knit wrist to 14-inch gauntlet for welding and furnace work. Tell us what fails first on the glove you use now: the palm, the fingertips, the seam at the thumb or the cuff. Each points at a different fix — a palm patch, a thicker hide, a welted seam or a different cut. That single answer is worth more than a specification list, because it tells us where the load actually goes on the hand. ### Detail **Hide matched to the job** Cowhide for abrasion and heat, goatskin for feel and dexterity, pigskin for wet-dry flexibility. We do not sell one hide as a universal answer. **Pattern before decoration** Gunn cut puts the seam away from the wear point; keystone thumb improves grip and reduces twisting. These details decide comfort more than the logo does. **Reinforcement where it counts** Palm patches, thumb crotch reinforcement and welted seams extend life in rigging and masonry, where the first failure is always the same spot. ### Specification - Leathers: Split cowhide, goatskin, grain pigskin, grain cowhide - Cuts: Gunn cut, clute cut, driver style - Thumb: Keystone or wing thumb - Cuff: Knit wrist, safety cuff, 14 in gauntlet - Lining: Unlined, fleece, cotton - Sizes: M–XXL - MOQ: 500 pairs per style and color - Lead time: Samples 10–14 days · bulk 25–35 days ### Leather selection Choose by the failure you see: split cowhide for sparks and abrasion, goatskin where feel and durability both matter, pigskin where the glove cycles between wet and dry. | Leather | Abrasion | Heat | Feel | Best for | | --- | --- | --- | --- | --- | | Split cowhide | High | High | Low–medium | Welding, masonry, heavy handling | | Goatskin | Medium–high | Medium | High | Rigging, driving, general site work | | Grain pigskin | Medium | Medium | High | Wet-dry handling, farming, logistics | | Grain cowhide | High | Medium | Medium | Driving, fork lift, general purpose | ### Questions **What is the difference between split and grain leather?** Split leather comes from the lower layers of the hide and is tougher and more abrasion-resistant. Grain leather keeps the outer surface, so it is smoother, more flexible and better for feel. **Are leather gloves suitable for welding?** Yes, split cowhide gauntlets are the standard for stick and MIG welding. For TIG, a thinner goatskin glove gives the finger control needed to feed wire. **Can leather gloves be washed?** They can be wiped and air-dried, but soaking leather degrades it. For washable heavy-duty work, a coated knit is usually the better choice. **Do you offer custom branding on leather?** Yes — embossed or printed logo on the cuff or back, woven labels and custom carton marks. Branding is confirmed on the sample before bulk. Laser engraving is not recommended on split leather, because the burnt edge hardens and cracks as the glove flexes. A debossed leather patch is a more durable mark on split hide. ### Related - Welding Gloves: https://workglovesfactory.com/welding-gloves/ - Heat Resistant Gloves: https://workglovesfactory.com/heat-resistant-gloves/ - Cut Resistant Gloves: https://workglovesfactory.com/cut-resistant-gloves/ - Construction Gloves: https://workglovesfactory.com/construction-gloves/ --- ## Work Glove Manufacturer URL: https://workglovesfactory.com/work-glove-manufacturer/ Section: Custom Manufacturing Primary topic: gloves manufacturer A factory that knits, dips, cuts and sews under one roof — so the liner, coating and fit are controlled by the same team. ### Overview A work glove manufacturer runs a long process for a small product: yarn, knitting, coating, curing, cutting, sewing, pairing and packing. When those steps sit in different factories, the liner that arrives is not always the liner that was quoted, and the size grading drifts between batches. We keep the core steps together. That lets us control gauge, coating weight and size consistency, and it lets us make a counter-sample quickly when a buyer needs a specific liner or palm. It also means we can say no to a request we cannot build well, instead of outsourcing it and hoping. ### Detail **One team, one spec** Knitting, dipping, cutting and sewing are coordinated against the same approved sample, so a reorder matches the first order instead of drifting. **Counter-samples, not catalogues** Send a glove you use today. We match the build and send a counter-sample in 7–10 days, with the differences written down so you can judge them. **Private label as standard** Logo, label, color and packaging are part of the normal order flow, not a separate project. Artwork is approved before bulk. ### Specification - Core processes: Knitting, coating and dipping, cutting, sewing, packing - Product range: Coated knit, cut gloves and sleeves, leather, impact, insulated, cotton and canvas, disposable nitrile - MOQ: 500 pairs per style and color - Sampling: 7–10 days; stock samples for evaluation - Bulk lead time: 20–30 days after sample approval - Incoterms: FOB, CIF, DDP - Payment: 30% deposit, balance before shipment - Shipping: Sea, rail and air; cartons palletized on request ### What we make and how The table is a map of the range, not a stock list. Every family is built to the liner, coating and finish confirmed on your approved sample. | Product family | Liner / material | Coating or finish | Typical buyer | | --- | --- | --- | --- | | Coated knit | Polyester, nylon, HPPE | PU, nitrile, PVC, foam latex | Distributors, MRO brands | | Cut resistant | HPPE, glass fiber, steel | PU, nitrile, leather palm | Industrial safety brands | | Impact | Knit + TPR shell | Nitrile, PU, synthetic leather | Construction suppliers | | Leather | Cowhide, goatskin, pigskin | Unlined or lined | Welding, rigging distributors | | Insulated | Acrylic or fleece lining | Nitrile, PVC | Outdoor and cold storage | | Cotton and canvas | Cotton jersey, cotton cloth or cotton canvas | Dots, band top or knit wrist | General duty, landscaping, distribution | | Cut sleeves | HPPE knit tube | 18 in or 24 in, thumb slot optional | Metal and glass handlers | | Disposable nitrile | Nitrile film, 3–5 mil | Powder-free, industrial grade | Food handling, workshops | ### Questions **Are you a factory or a trading company?** We are a manufacturer with knitting, dipping, cutting and sewing coordinated in-house. If a request falls outside our lines, we say so rather than passing it to an unknown subcontractor. **How do we start a first order?** Send the glove type, quantity, destination and any sample you already use. We reply with a shortlist, sample plan and indicative price. A counter-sample follows once the build is agreed. **Can you handle our packaging and carton marks?** Yes — printed polybags, header cards, hang tags, size stickers and carton marks. Send artwork in AI or PDF and we return a mock-up for approval before production. **What information do you need for a quotation?** Glove type or current sample, target quantity, sizes and ratio, destination port or door, and any branding or packaging requirement. With those five points we can quote without a round of questions. Anything else can follow once the numbers are in front of you. ### Related - Custom Work Gloves: https://workglovesfactory.com/custom-work-gloves/ - Wholesale Work Gloves: https://workglovesfactory.com/wholesale-work-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ - Contact: https://workglovesfactory.com/contact/ --- ## ANSI Cut Levels Explained: A1 to A9 URL: https://workglovesfactory.com/guides/ansi-cut-levels/ Section: Guides Primary topic: ansi glove ratings A1 to A9 in plain terms: what the test measures, what each level means on the floor, and how to choose without over-buying. ### Overview ANSI cut levels run from A1 to A9 under ANSI/ISEA 105. The test uses a rotating circular blade under a controlled load; the result is the load, in grams, that the glove withstands before the blade cuts through. Higher letters mean more resistance, not necessarily a better glove for your job. The practical mistake is buying the highest level available. Every step up usually adds weight, heat and stiffness, and a glove that is too heavy gets removed at the workstation. The right level is the lowest one that covers the hazard for the duration of the task. ### Detail **What the number means** A4 means the liner withstood 1,500 g of load in the test. It is a relative comparison between materials, not a promise about a specific blade, speed or angle on your line. **ANSI and EN are not interchangeable** ANSI uses a straight blade under load; EN388:2016 uses a circular blade and reports cut as a 0–5 rating plus a TDM letter A–F. Do not convert one to the other by formula. **Level is a property of the liner** Coating, color and cuff do not change the cut level. If two gloves share a liner and gauge, they share the level, regardless of the palm finish. ### Specification - Standard: ANSI/ISEA 105-2016 - Scale: A1 (200 g) to A9 (6,000 g) - Test: Rotating circular blade under increasing load - European equivalent: EN388:2016 cut index 0–5 plus TDM A–F - Affects: Liner fiber, blend ratio, gauge - Common range: A2–A5 covers most general industry ### ANSI/ISEA 105 cut levels Load values are the test thresholds used to assign each level. | Level | Load | Relative protection | Typical application | | --- | --- | --- | --- | | A1 | 200 g | Lowest rated | Light assembly, packing, general handling | | A2 | 500 g | Light | Warehouse, maintenance, light metal | | A3 | 1,000 g | Medium | Sheet metal, glass, automotive | | A4 | 1,500 g | Medium–high | Metal fabrication, recycling, construction | | A5 | 2,200 g | High | Heavy plate, demolition, scrap | | A6 | 3,000 g | Very high | Sharps, heavy scrap, glass demolition | | A7 | 4,000 g | Extreme | Specialist metal and glass tasks | | A8 | 5,000 g | Extreme | Rare; heavy sharp-edge environments | | A9 | 6,000 g | Highest rated | Rare; specific high-risk operations | ### ANSI vs EN388 at a glance Buyers serving both markets usually specify the level for each market separately rather than converting. | Topic | ANSI/ISEA 105 | EN388:2016 | | --- | --- | --- | | Cut scale | A1–A9 | 0–5 (Coup test) plus A–F (TDM) | | Blade | Straight blade, linear pass | Circular blade, rotating | | Reporting | Single cut level | Four digits plus TDM letter | | Market | United States | Europe and many export markets | | Cross-walk | No official conversion | No official conversion | ### Questions **What cut level do I need for sheet metal?** A3 or A4 covers most sheet-metal handling. Choose A4 when edges are burred or the part is heavy enough to slip; A3 is usually enough for light gauge with controlled handling. **Is A9 the safest choice?** Not automatically. A9 gloves are dense and stiff, which increases hand fatigue and reduces the time a worker keeps them on. Use the lowest level that covers the hazard. **Does coating change the cut level?** No. The cut rating comes from the liner. Coating affects grip, abrasion and liquid resistance, so choose it for the surface, not for the cut number. **How often should cut gloves be replaced?** When the liner is worn thin at the palm or fingertips, or when the glove no longer passes a visual check for holes. Cut performance drops as the liner abrades, even if the coating still looks intact. ### Related - Cut Resistant Gloves: https://workglovesfactory.com/cut-resistant-gloves/ - Puncture Resistant Gloves: https://workglovesfactory.com/puncture-resistant-gloves/ - Safety Gloves: https://workglovesfactory.com/safety-gloves/ - Glove Size Chart: https://workglovesfactory.com/guides/glove-size-chart/ --- ## Jersey & Cotton Work Gloves URL: https://workglovesfactory.com/jersey-cotton-work-gloves/ Section: Work Gloves Primary topic: jersey gloves The light general-duty glove: cotton jersey, knit wrist, optional PVC dots — inexpensive, breathable and easy to reorder by the bale. ### Overview Jersey gloves are the base layer of every glove program. They keep hands clean, reduce minor abrasion and give a bit of warmth without reducing feel. For handling that does not involve sharp edges or oil, they are often enough — and they cost a fraction of a coated glove. We make them in 7 oz and 8 oz cotton jersey, clute cut for a straight, comfortable fit, with knit wrist or band top. PVC dots on one or both palms add grip for handling cartons, bricks and timber. Weight is the usual first question. 7 oz is the lightest build and where most sites start; 8 oz feels noticeably more substantial in the hand and lasts longer on rough concrete and timber for a small cost increase. For visitors and one-off tasks, plain 7 oz with a knit wrist is enough. For a yard or loading crew that wears the glove every day, 8 oz with dots on both sides holds up better and can be worn on either hand, which halves the sorting problem when gloves come back from the wash. Alongside jersey we also build cotton cloth and cotton canvas gloves: a heavier cotton shell for buyers who want more abrasion life than jersey but do not need a coated palm. The pattern is the same clute cut with a knit wrist or band top, so sizing and reordering stay simple. ### Detail **Cheap enough to stock** Jersey gloves are the lowest-cost option in the range, which makes them practical for visitors, light tasks and overflow crews where a coated glove would be wasted. **Breathable cotton** Open cotton knit lets heat out. In warm warehouses that matters more than abrasion resistance, because the glove stays on. **Dots add grip** PVC dots on one or both sides improve grip on boxes, bricks and timber, and add a little abrasion resistance at the contact points. ### Specification - Material: Cotton jersey 7 oz / 8 oz; cotton yarn 400–800 g; cotton cloth, cotton/nylon blend or cotton canvas on request - Yarn weights: 400, 500, 600, 650, 750 and 800 g builds - Cut: Clute cut, straight thumb - Cuff: Knit wrist or band top - Options: PVC dots one side / both sides, bleached or natural, single-glove packing - Sizes: M–2XL; one size on selected styles - Length: 22–26 cm overall, style dependent - MOQ: 1,000 pairs per style (light gloves pack smaller) - Packaging: 12 pairs per polybag, 600 pairs per bale - Lead time: Samples 7–10 days · bulk 20–30 days ### Jersey options Plain knit wrist is the cheapest build; band top sits higher and stays on in yard work. Dots are worth adding only where the load is dry and smooth. | Build | Weight | Grip | Typical use | | --- | --- | --- | --- | | Plain jersey, knit wrist | 7 oz | Low | Packing, light handling, visitors | | Plain jersey, band top | 8 oz | Low | General duty, yard work | | PVC dotted one side | 8 oz | Medium | Cartons, bricks, timber | | PVC dotted both sides | 8 oz | Medium–high | Reversible use, rough handling | | Cotton cloth, band top | 8 oz | Low | General duty, housekeeping, distribution | | Cotton yarn, PVC dotted | 8 oz | Medium | Packing, garden and yard work | | Cotton canvas, clute cut | Quoted per style | Low–medium | Masonry, landscaping, timber | ### Cotton yarn build weights Gram weights follow the yarn build scale; the weight basis is confirmed on the approved spec. | Build | Yarn weight | Density | Typical use | | --- | --- | --- | --- | | Light | 400 g | Dense | Packing, inspection, liner under a coated glove | | Light–medium | 500 g | Dense | General handling, warehouse | | Medium | 600 g | Medium–heavy | Yard, loading, general duty | | Medium–heavy | 650 g | Heavy | Construction support, rough handling | | Heavy | 750 g | Heavy | Rough handling, cold weather | | Extra heavy | 800 g | Extra heavy | Heavy duty, cold outdoor work | ### Questions **Are jersey gloves cut resistant?** No. Cotton jersey offers no meaningful cut protection. If the task involves sharp edges, step up to an HPPE or glass-fiber liner with a rated cut level. **What is the difference between clute and gunn cut?** Clute cut uses a straight thumb and fewer seams, which is cheaper and comfortable for light work. Gunn cut places seams away from wear points and is used for heavier leather gloves. **Can jersey gloves be washed?** Yes, they can be machine-washed and reused a limited number of times. They are usually treated as a consumable and replaced when soiled or worn through. **Do you offer branded jersey gloves?** Yes. Printed logos on the back of the hand can be added as part of a private-label order, typically from 1,000 pairs per style. **Do you make canvas and cotton cloth gloves as well as jersey?** Yes. Cotton cloth and cotton canvas gloves are built on the same clute pattern, with knit wrist or band top. Canvas is the heavier option for masonry, landscaping and timber handling; jersey stays the lighter, breathable choice for packing and general duty. **Do you supply white nylon gloves?** Yes, as a separate knit family: 13G or 15G seamless nylon with a PU or nitrile palm, used for light assembly, inspection and packing. Nylon is thinner and dries faster than cotton jersey, and it is specified where lint and fit matter. The nylon-liner builds are on the PU coated gloves page. ### Related - PU Coated Gloves: https://workglovesfactory.com/pu-coated-gloves/ - Grip Work Gloves: https://workglovesfactory.com/grip-work-gloves/ - Warehouse Gloves: https://workglovesfactory.com/warehouse-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## Waterproof Work Gloves URL: https://workglovesfactory.com/waterproof-work-gloves/ Section: Work Gloves Primary topic: waterproof work gloves Fully coated shells over seamless liners: hands stay dry in wet handling, washdown and cold storage work. ### Overview A palm-dipped glove keeps your grip dry but lets water in through the back. Waterproof work gloves need a full coating — nitrile or PVC over a seamless knitted liner — with a sealed cuff that stops water running down the wrist. The trade-off is breathability. A fully coated glove traps heat and moisture, so we size the liner and coating weight to the job: thin for dexterity in wet packing, heavier for cold and abrasive washdown work. Gauntlet cuffs shed water; knit wrists are for light splash only. A simple test before you commit: fill the glove with water and hold it cuff-up for a minute. A palm-dipped glove will weep through the knitted back almost immediately; a proper full shell holds. When you specify, tell us the depth and duration of exposure — splash, immersion to the wrist, or full arm — because that decides cuff length and coating weight more than the material does. ### Detail **Full shell, not just a palm** The coating covers the whole hand and seals at the cuff, so water does not enter through the back of the glove during immersion or heavy spray. **Grip when wet** A rough or sandy finish holds wet and slimy surfaces far better than a smooth shell. We match the finish to what you are lifting. **Cold and wet together** A fleece-lined version adds insulation for cold storage and winter outdoor work without letting water through the shell. ### Specification - Coating: Full nitrile or PVC, smooth / rough / sandy - Liner: Seamless cotton, polyester or fleece - Cuff: Gauntlet 30–35 cm or knit wrist - Waterproofing: Full shell with sealed cuff - Sizes: M–XXL - MOQ: 500 pairs per style and color - Packaging: 12 pairs per polybag, 120 pairs per carton - Lead time: Samples 7–10 days · bulk 20–30 days ### Waterproof builds Palm-dipped gloves are not waterproof. If the hand goes into water, specify a full shell. | Build | Water resistance | Insulation | Typical use | | --- | --- | --- | --- | | Full PVC, rough finish | Full immersion | None | Washdown, fisheries, cleaning | | Full nitrile, sandy | Full immersion | None | Wet handling, oil and water | | Full nitrile, fleece lined | Full immersion | Medium | Cold storage, winter outdoor | | Palm dip + knit wrist | Splash only | None | Light wet handling | ### Questions **Is a nitrile-coated glove waterproof?** Only if it is fully coated. A palm-dipped glove lets water through the knitted back and cuff. Ask for a full-shell build when the hand is immersed or heavily sprayed. **Can waterproof gloves be used with chemicals?** No. Waterproofing is not chemical protection. Chemical permeation needs a dedicated glove with breakthrough data for the specific substance. **How do I stop water running down the cuff?** Use a gauntlet cuff long enough to cover the jacket sleeve, and tighten the jacket over the glove rather than tucking the glove inside. A knit wrist only handles splash. **Do they get sweaty?** A full shell traps heat and moisture. For warm wet work choose a thinner liner; for cold work a fleece lining manages moisture better than a bare cotton liner. ### Related - PVC Coated Gloves: https://workglovesfactory.com/pvc-coated-gloves/ - Winter Work Gloves: https://workglovesfactory.com/winter-work-gloves/ - Grip Work Gloves: https://workglovesfactory.com/grip-work-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## PVC Coated Work Gloves URL: https://workglovesfactory.com/pvc-coated-gloves/ Section: Work Gloves Primary topic: pvc gloves Heavy, rough-finish PVC for wet and abrasive work where a thinner coating would be shredded in a shift. ### Overview PVC coated work gloves use the heaviest of the common coatings. They are chosen for rough, wet and abrasive work — concrete, masonry, agriculture, washdown — where a PU or nitrile palm would wear through quickly. The rough finish also gives a strong grip on wet and muddy surfaces. The cost is dexterity and breathability. PVC gloves are stiffer and warmer, so they suit tasks where protection and abrasion life matter more than feel. We build palm, three-quarter and full coatings on interlock or fleece liners. Compare PVC against nitrile on the surface you are actually working, not on a data sheet. On wet concrete, mortar and stone, the thick rough PVC film outlasts everything else in the range and keeps its grip as it wears. On oily metal it swells and loses shape; on anything needing fingertip control it is simply too stiff. A common pattern is PVC for the demolition and masonry phase of a job and a nitrile palm glove for the finishing work, bought on the same order so the crew is not choosing between them. ### Detail **Abrasion life** PVC takes rough surfaces that destroy thinner coatings. It is the practical choice for concrete, brick, stone and heavy wet handling. **Rough finish grip** The textured palm holds wet, muddy and oily surfaces. Smooth PVC is slippery when wet and is rarely the right finish for outdoor work. **Insulated options** A fleece-lined PVC glove handles cold wet work where a bare liner would leave hands numb by mid-shift. ### Specification - Coating: PVC, rough or smooth finish - Dip: Palm, 3/4 or full - Liner: Interlock cotton, polyester, fleece - Cuff: Safety cuff or 30 cm gauntlet - Sizes: M–XXL - MOQ: 500 pairs per style and color - Packaging: 12 pairs per polybag, 120 pairs per carton - Lead time: Samples 7–10 days · bulk 20–30 days ### PVC configurations Palm dip keeps the back breathable, three-quarter dip covers more of the hand, and full dip is the wet-work build. Interlock liners are cooler; fleece liners are warmer. | Build | Dexterity | Abrasion | Typical use | | --- | --- | --- | --- | | Palm, rough finish | Medium | High | Masonry, concrete, bricks | | 3/4, rough finish | Medium | High | Wet outdoor handling | | Full, rough finish | Low | Very high | Washdown, agriculture, heavy wet | | Full, fleece lined | Low | Very high | Cold wet work, cold storage | ### Questions **PVC or nitrile for wet work?** PVC for rough, abrasive and muddy surfaces where abrasion life dominates. Nitrile for oil and where more flexibility is needed. Both need a full coating if the hand is immersed. **Are PVC gloves oil resistant?** PVC resists oils reasonably well but swells with some solvents. For continuous oil contact, sandy nitrile is usually the better choice. **Why are PVC gloves stiffer?** PVC is a heavier coating and needs a thicker film to perform. That stiffness is the price of abrasion life; for precision work choose PU or nitrile instead. **Can PVC gloves be recycled?** They are not accepted in normal recycling streams. Plan them as a consumable and dispose of them through your normal industrial waste route. Do not burn worn PVC on site: the smoke is corrosive and the residue has to be handled as hazardous waste. ### Related - Waterproof Work Gloves: https://workglovesfactory.com/waterproof-work-gloves/ - Nitrile Coated Gloves: https://workglovesfactory.com/nitrile-coated-gloves/ - Construction Gloves: https://workglovesfactory.com/construction-gloves/ - Grip Work Gloves: https://workglovesfactory.com/grip-work-gloves/ --- ## Warehouse & Logistics Gloves URL: https://workglovesfactory.com/warehouse-gloves/ Section: Industries Primary topic: warehouse gloves Thin palms, touchscreen fingertips and a price that survives high turnover — gloves for picking, packing and loading. ### Overview Warehouse work is repetitive, not violent. Warehouse gloves therefore have to let people scan, type, peel labels and pick small items, then survive cartons, strapping and the occasional box cutter. That points to a thin PU palm on a fine-gauge liner, not a heavy cut glove. Where box cutters are used all shift, an A1–A2 cut liner is sensible without losing feel. Hi-vis backs help in busy loading areas, and touchscreen fingertips avoid the constant glove-off-glove-on cycle at handheld scanners. Most warehouse glove programmes fail on sizing and issue rather than on the glove itself. A one-size approach means the smaller half of the workforce wears a glove that bunches at the fingertips, loses the ability to feel a label, and quietly takes it off. Specify a real S–XXL split from your headcount, print the size inside the cuff, and keep the two middle sizes at the pick face so a replacement does not mean a walk to the stores. ### Detail **Dexterity for scanning** A 15G nylon liner with a thin PU palm lets workers use handheld scanners and touchscreens without removing the glove. **Cut level without bulk** A1–A2 HPPE liners add cut protection at the fingertips where box cutters catch, while keeping the palm thin enough to feel labels and small parts. **Visible in the aisle** A fluorescent back and reflective trim make hands visible to forklift drivers — a low-cost addition that sites usually keep once they try it. ### Specification - Liner: 15G nylon or 13G HPPE - Palm: PU, thin nitrile or foam nitrile - Cut level: A1–A2 for cutter handling - Features: Touchscreen fingertips, hi-vis back option - Sizes: US 6–10 - MOQ: 500 pairs per style and color - Packaging: 10 pairs per polybag, 200 pairs per carton - Lead time: Samples 7–10 days · bulk 20–30 days ### Warehouse task to glove Match the glove to the task at the pick face. Cut level only needs to rise where box cutters are used all shift. | Task | Glove | Why | | --- | --- | --- | | Picking small items | 15G PU palm | Feel and light abrasion | | Packing and taping | 13G PU, touchscreen | Scanner use, carton abrasion | | Loading / unloading | Nitrile palm, hi-vis | Grip and visibility | | Box cutter use | A2 HPPE, PU palm | Cut protection at fingertips | | Cold store | Insulated nitrile palm | Cold plus grip | ### Questions **Do warehouse gloves need cut protection?** Only where cutters, strapping or sharp packaging are handled. For pure picking and packing, a thin PU glove is more comfortable and more likely to be worn. **Can gloves work with touchscreens?** Yes. Conductive fingertips on thumb and index work with capacitive scanners and tablets. Confirm the device type when ordering so the yarn matches. **How do we control glove cost per worker?** Issue by task rather than one glove for the whole floor, and use a washable PU style where possible. Matching the glove to the task usually cuts consumption more than negotiating price. **Can we get sizes for a mixed workforce?** Yes. We pack S–XXL in the ratio you specify, so each site receives the size mix it actually uses instead of a flat carton. Send the split you issue today and we will match it on the packing list. ### Related - PU Coated Gloves: https://workglovesfactory.com/pu-coated-gloves/ - Grip Work Gloves: https://workglovesfactory.com/grip-work-gloves/ - Hi-Visibility Gloves: https://workglovesfactory.com/high-visibility-work-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## Wholesale Work Gloves URL: https://workglovesfactory.com/wholesale-work-gloves/ Section: Custom Manufacturing Primary topic: wholesale work gloves Mixed pallets, private label and a reorder plan that keeps your best sellers in stock without over-ordering the rest. ### Overview Wholesale work glove buyers care about three things: a landed cost they can build a margin on, a reorder that matches the first shipment, and packaging that survives their own channel. The glove itself is often already decided by their customers. We quote FOB or DDP, pack mixed pallets across families, and set a size ratio per carton so your warehouse does not end up with a pallet of XXL. For repeat business we plan production against a rolling forecast rather than waiting for the stockout. Start with a sample kit rather than a container. Three to six families, one or two sizes each, is enough to test the glove on your customers’ actual tasks and to see whether the packaging survives your channel. Once a family proves out, the reorder can be planned against a rolling forecast, so production slots are booked before the stockout — usually the difference between a smooth season and paying air freight for a fast mover. ### Detail **Mixed pallets** Combine coated, leather and insulated families on one order to reach a container or pallet target without committing to a single style. **Margin-aware pricing** Pricing is quoted at your quantity and packaging level, with the cost of branding and carton work shown separately so you can see where margin goes. **Reorder discipline** We keep the approved sample and spec on file so the second order matches the first, and plan bulk against your forecast instead of a rush order. ### Specification - Customer type: Distributors, importers, MRO suppliers - MOQ: 500 pairs per style and color - Packing: Mixed pallets, custom size ratios - Branding: Private label, neutral packaging - Terms: FOB, CIF, DDP - Payment: 30% deposit, balance before shipment - Lead time: 20–30 days after sample approval - Documentation: Commercial invoice, packing list, B/L ### Wholesale order shapes Order shape follows the channel. A sample kit is the low-risk way to test three to six families before committing to a pallet or container. | Buyer | Typical order | Packaging | Best next step | | --- | --- | --- | --- | | Safety distributor | 3–6 families, mixed pallet | Neutral polybag or own brand | Sample kit across families | | Importer / container buyer | 1–3 families, full container | Private label | Landed cost quote (DDP) | | MRO supplier | 2–4 fast movers | Plain cartons | Reorder plan | | Own-brand retailer | 1–2 styles, deep buy | Retail packaging | Packaging mock-up | ### Questions **Do you have a distributor price list?** We quote per order rather than publish a list, because price moves with quantity, coating, packaging and destination. Send the families, quantities and port and you will get a firm quote. **Can I mix styles to reach a container?** Yes. Mixed pallets and mixed containers are normal for distributor orders. Each style still carries the 500-pair minimum. **Do you offer exclusivity?** For a defined territory and a committed annual volume, exclusivity can be discussed. It is a commercial agreement, not a standard term, so it needs a conversation before the first order. **What are the payment terms?** Standard terms are 30% deposit with the balance before shipment. Terms can be reviewed after a track record of repeat orders. Longer terms are usually tied to a committed forecast rather than to a single shipment. ### Related - Custom Work Gloves: https://workglovesfactory.com/custom-work-gloves/ - Work Glove Manufacturer: https://workglovesfactory.com/work-glove-manufacturer/ - Work Gloves: https://workglovesfactory.com/work-gloves/ - Contact: https://workglovesfactory.com/contact/ --- ## Winter Work Gloves URL: https://workglovesfactory.com/winter-work-gloves/ Section: Work Gloves Primary topic: winter work gloves Warmth without losing grip: fleece or acrylic linings, nitrile palms that stay soft in the cold, and a waterproof shell when the work is wet. ### Overview Winter work gloves have to solve a simple problem: cold hands lose grip strength before they lose feeling, which is why they fail in two ways — not warm enough, or too bulky to hold a tool. The fix is a lining that traps warm air close to the skin and a palm that stays flexible below freezing. We build three cold-weather families: a knit winter glove with a fleece lining and nitrile palm for dry cold, a fully coated waterproof version for wet cold, and a heavy insulated gauntlet for outdoor work at lower temperatures. EN511 cold ratings are stated on the approved spec. Get the temperature and the duration right before choosing a build. A fleece-lined knit glove is comfortable at −5 °C on a two-hour outdoor task and useless at −25 °C in a cold store where hands are wet. Tell us the lowest temperature, whether the hand stays wet or dry, and how long a shift runs, and we will point to the build rather than the warmest glove in the range, which is often too bulky to be worn for a full shift. ### Detail **Warmth where it is lost** Fleece or acrylic terry lining on the back of the hand, with a thinner palm so fingers can still close around a handle. **Palm stays soft** Nitrile and PU palms remain flexible in cold conditions; PVC stiffens. For sub-zero handling, the palm choice matters as much as the lining. **Dry cold vs wet cold** A knit back is fine for dry cold. For snow, rain or washdown, specify a full shell so the insulation does not soak and lose its warmth. ### Specification - Lining: Fleece, acrylic terry, or 3-layer - Palm: Sandy nitrile, foam nitrile, PVC - Waterproof: Knit back (dry cold) or full shell (wet cold) - Cold rating: EN511 stated per style - Cuff: Knit wrist or gauntlet - Sizes: M–XXL - MOQ: 500 pairs per style and color - Lead time: Samples 10–14 days · bulk 25–35 days ### Winter builds Wetness decides the build before temperature does. A fully coated shell is the difference between a dry-cold glove and one that soaks through. | Build | Conditions | Warmth | Dexterity | | --- | --- | --- | --- | | Fleece-lined knit, nitrile palm | Dry cold | Medium | High | | Acrylic terry, full nitrile | Wet cold | High | Medium | | 3-layer insulated, gauntlet | Severe cold, outdoor | Highest | Low | | Thin liner glove + shell | Variable | Medium | Highest | ### Questions **What does EN511 measure?** EN511 rates cold protection on three scales: convective cold, contact cold and water penetration. A rated glove carries three digits, and the contact-cold digit is the one that matters for handling cold metal. **Can I use winter gloves in a freezer?** Yes, but choose the build for the temperature and duration. For long shifts below −20 °C, a 3-layer insulated gauntlet is more reliable than a fleece-lined knit. **Do insulated gloves lose grip?** Thicker linings reduce feel. A thin nitrile palm on an insulated back keeps grip usable; a full PVC shell is warmer but much less dexterous. **Can winter gloves be touchscreen compatible?** Yes, conductive fingertips can be added. On insulated gloves the fingertip pad stays thin, so touch still works without exposing the finger. ### Related - Waterproof Work Gloves: https://workglovesfactory.com/waterproof-work-gloves/ - Nitrile Coated Gloves: https://workglovesfactory.com/nitrile-coated-gloves/ - Hi-Visibility Gloves: https://workglovesfactory.com/high-visibility-work-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## Welding Gloves URL: https://workglovesfactory.com/welding-gloves/ Section: Work Gloves Primary topic: welding gloves Split cowhide gauntlets for stick and MIG, thin goatskin for TIG — heat, sparks and spatter without losing the wire hand. ### Overview Welding gloves are chosen by process. Stick and MIG throw spatter and need a thick split-cowhide gauntlet with a wide cuff. TIG needs finger feel to feed wire, so a thin goatskin glove with a short cuff works better than a heavy gauntlet that fights every movement. The seams matter as much as the leather. Welted seams keep sparks out, Kevlar-type stitching survives contact heat, and a reinforced thumb crotch holds up where the rod hand rests against the work. The three failure modes we see on welding orders are burn-through at the cuff, fingers that stiffen after a week, and a glove too thick to feel the torch. Split leather takes spatter better than a thin chrome-tanned hide, a gauntlet cuff keeps sparks out of the wrist, and a heat-resistant seam stops the glove unravelling along the finger gussets. Tell us the process — MIG, stick or TIG — because TIG needs a thin, sensitive glove while stick welding needs thickness and a long cuff. ### Detail **Process-matched builds** Heavy split cowhide for stick and MIG, medium goatskin for general fabrication, thin goatskin for TIG. One glove does not cover all three well. **Sparks kept out** Welted seams, a gauntlet cuff that overlaps the sleeve and a reinforced thumb crotch stop spatter reaching the skin at the points where it usually gets in. **Heat where it is needed** Leather thickness is concentrated on the palm, thumb and cuff — the surfaces that meet hot work — rather than making the whole glove rigid. ### Specification - Leather: Split cowhide (stick/MIG), goatskin (TIG/general) - Cuff: 14 in gauntlet, 4–5 in for TIG - Stitching: Heat-resistant aramid thread - Lining: Unlined or cotton lined - Sizes: M–XXL - MOQ: 500 pairs per style - Packaging: 10 pairs per polybag, 60–100 pairs per carton - Lead time: Samples 10–14 days · bulk 25–35 days ### Welding process to glove The process sets the leather and cuff. Going heavier than the process needs costs finger feel without adding protection. | Process | Glove | Cuff | Why | | --- | --- | --- | --- | | Stick (SMAW) | Heavy split cowhide | 14 in gauntlet | Spatter and radiant heat | | MIG (GMAW) | Split cowhide or pigskin | 14 in gauntlet | Spatter plus wire control | | TIG (GTAW) | Thin goatskin | 4–5 in cuff | Finger feel for filler wire | | Spot / resistance | Goatskin or nitrile-dipped | Short cuff | Light spatter, dexterity | ### Questions **Which glove is best for TIG welding?** A thin goatskin glove with a short cuff. TIG produces little spatter but requires precise filler-wire control, so a heavy gauntlet is counterproductive. **Are welding gloves heat rated?** Leather resists contact heat and spatter, but welding gloves are not furnace gloves. For sustained contact with hot parts, specify a heat-resistant glove rated for the temperature and duration. **Can welding gloves be branded?** Yes. Embossed or printed logos on the cuff, plus woven labels and custom cartons, are available for private-label orders. **How long should a welding glove last?** It depends on process and handling. Failure usually starts at the thumb crotch or the cuff seam; reinforcement at those points extends life more than a thicker palm. ### Related - Heat Resistant Gloves: https://workglovesfactory.com/heat-resistant-gloves/ - Leather Work Gloves: https://workglovesfactory.com/leather-work-gloves/ - Construction Gloves: https://workglovesfactory.com/construction-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## Heat-Resistant Work Gloves URL: https://workglovesfactory.com/heat-resistant-gloves/ Section: Work Gloves Primary topic: heat resistant gloves Aramid and leather builds for hot parts, trays and light furnace work — rated by contact temperature and time, not by a slogan. ### Overview Heat-resistant work gloves depend on temperature and time together. A glove that handles a 200 °C tray for ten seconds is not the same glove that handles a 300 °C casting for a minute. EN407 contact-heat levels exist precisely because both numbers matter. We build heat gloves around aramid fiber, leather and aluminized options: thin aramid knits for bakery and light handling, leather-palm aramid for foundry and glass, and heavier builds for short contact with hotter parts. Tell us the surface temperature and dwell time, and we match the build. Contact heat and radiant heat are different problems. A glove rated for handling a 250 °C part for fifteen seconds is not the same as one that stands next to a furnace door for a shift. Give us the surface temperature, how long the hand is in contact, and whether there is flame or molten spatter, and the material choice follows: aramid knits for radiant heat, leather or aluminised backs for contact, and a different approach entirely if molten metal is involved. ### Detail **Temperature and time** We ask for both before recommending a build. A glove rated for short contact is not a furnace glove, and treating it as one is how burns happen. **Aramid where it counts** Aramid liners resist heat without melting, and leather palms add abrasion and radiant protection at the contact surface. **Dexterity for hot handling** Thin aramid knits work for bakery trays and light parts where feel matters; heavier leather builds suit hot castings where grip strength matters more. ### Specification - Materials: Aramid knit, split cowhide, aluminized option - Contact heat: Up to 350 °C for short contact (build dependent) - Standard: EN407 contact heat levels stated per style - Cuff: Knit wrist, 14 in gauntlet - Sizes: M–XXL - MOQ: 500 pairs per style - Packaging: 10 pairs per polybag, 100 pairs per carton - Lead time: Samples 10–14 days · bulk 25–35 days ### Heat glove selection Heat ratings depend on contact time. Confirm both values with the sample before use on hot work. | Build | Contact heat | Dexterity | Typical use | | --- | --- | --- | --- | | Aramid knit, nitrile dots | Up to 250 °C, short | High | Bakery, light trays, lab | | Aramid + leather palm | Up to 300 °C, short | Medium | Foundry, glass, metal parts | | Heavy split cowhide gauntlet | Up to 350 °C, short | Low | Furnace doors, hot castings | | Aluminized back, leather palm | Radiant heat | Low | Furnace and kiln work | ### Questions **Can these gloves handle open flame?** No. Heat-resistant work gloves handle contact heat and radiant heat for short periods. Open flame, molten metal and structural firefighting need dedicated protective equipment. **What does EN407 contact heat level mean?** It records the highest contact temperature the glove can withstand for 15 seconds without the inner surface rising more than a set amount. Higher levels mean hotter contact, not unlimited time. **Are aramid gloves cut resistant too?** Aramid adds some cut resistance, but it is not a substitute for an HPPE cut glove. Where both heat and sharp edges exist, specify both requirements. **Can heat gloves be repaired?** Minor seam damage can sometimes be re-stitched, but heat exposure degrades fibers invisibly. Replace gloves that have been exposed beyond their rated contact time. **Is a heat-resistant glove the same as an insulated glove?** No. A heat-resistant glove resists contact and radiant heat on the outside; an insulated glove traps warmth for cold work. For hot handling, specify the contact temperature and dwell time; for cold, the lowest temperature and shift length. A glove built for one job is not a substitute for the other. ### Related - Welding Gloves: https://workglovesfactory.com/welding-gloves/ - Leather Work Gloves: https://workglovesfactory.com/leather-work-gloves/ - Cut Resistant Gloves: https://workglovesfactory.com/cut-resistant-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## Grip Work Gloves URL: https://workglovesfactory.com/grip-work-gloves/ Section: Work Gloves Primary topic: grip gloves When the part is wet, oily or smooth, grip is the whole job: sandy nitrile and crinkle finishes that hold on where smooth palms slip. ### Overview Grip work gloves cannot be specified by a single property. A glove that grips a dry box can be useless on an oily pipe, and a glove that holds wet glass may wear out on dry steel. The finish — sandy, crinkle, foam or dotted — decides which surface the glove actually holds. We match the finish to the contaminant and the part shape: sandy nitrile for oil and water, crinkle nitrile for wet smooth surfaces, PVC dots for dry cartons. If a buyer describes the part and the contaminant, we can usually name the right finish in one reply. The same glove can hold a dry steel bar perfectly and still be useless on a wet plastic drum, and a soft palm that grips glass offers nothing on an oily shaft. Describe the object, its surface and its condition — dry, wet, oily, dusty or icy — and we match the finish: smooth nitrile for dry precision work, sandy nitrile for wet and oily, PVC dots or crinkle latex for dry abrasive surfaces, and a rough PVC film for mud. ### Detail **Finish matched to contaminant** Sandy nitrile for oil, crinkle for wet smooth parts, foam for dry abrasive handling. The chemistry is similar; the surface texture is what changes grip. **Channeled grip** Textured coatings push liquid away from the contact patch instead of letting it form a film. That is why sandy finishes outperform smooth palms when hands are wet. **Still a work glove** Grip builds keep a knit back for breathability and a rated liner where cut protection is needed, so grip does not come at the cost of the rest of the glove. ### Specification - Coatings: Sandy nitrile, crinkle nitrile, foam nitrile, foam latex, PVC dots - Liner: 13G polyester, 15G nylon, HPPE blend - Point-dot build: Nylon liner, PVC point-dot palm, lightweight high-stretch - Foam rubber build: Grey yarn, green foam latex dip, one size, 12 pairs per bag - Grip surfaces: Wet, oily, smooth, dry abrasive - Cut options: A1–A4 - Sizes: US 6–11; one size on point-dot and foam rubber builds - MOQ: 500 pairs per style and color - Packaging: 12 pairs per polybag, 120–240 pairs per carton - Lead time: Samples 7–10 days · bulk 20–30 days ### Grip by contaminant Match the finish to the contaminant first, then the part shape. A finish that grips oil can polish on dry steel. | Contaminant | Best finish | Avoid | Note | | --- | --- | --- | --- | | Oil / grease | Sandy nitrile | PU, smooth PVC | Nitrile resists oil; PU softens | | Water / wet parts | Crinkle or sandy nitrile | Flat palm | Texture channels water away | | Dry abrasive | Foam or flat nitrile | Smooth PU | Abrasion life beats texture here | | Dry cartons | PU or PVC dots | Sandy nitrile | Point-dot nylon is lightweight and high-stretch | | Wet handling | Foam latex | PU | Grey yarn, green dip, one size, 12 pairs per bag | | Glass (dry) | PU or foam nitrile | Rough PVC | Feel matters more than texture | ### Questions **What is the best glove for oily parts?** Sandy nitrile over a knit liner. Nitrile resists oil and the rough finish channels it away from the contact patch. PU palms soften and lose grip in oil. **Do grip gloves work when wet?** Textured nitrile works well on wet parts. Smooth palms and leather do not. For full immersion, choose a fully coated glove so water does not enter through the back. **Does more texture mean better grip?** No. Texture helps on wet and oily surfaces but can add drag on dry cartons and reduce feel on small parts. Match the finish to the surface. **Can grip gloves include cut protection?** Yes. Sandy nitrile is commonly applied over A2–A4 HPPE liners for handling sharp, oily parts such as sheet metal and glass. ### Related - Nitrile Coated Gloves: https://workglovesfactory.com/nitrile-coated-gloves/ - Waterproof Work Gloves: https://workglovesfactory.com/waterproof-work-gloves/ - Mechanic Gloves: https://workglovesfactory.com/mechanic-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## Construction Gloves URL: https://workglovesfactory.com/construction-gloves/ Section: Industries Primary topic: construction gloves Rebar, masonry, framing and site handling: A4–A5 cut liners, TPR knuckles and a hi-vis back that survives concrete dust. ### Overview Construction work brings several hazards in one shift: rebar and wire edges, struck knuckles, abrasive concrete, and traffic on site. A construction glove that only covers one of them gets swapped constantly, which is when injuries happen. We build site gloves that combine an A4–A5 HPPE liner with TPR back protection and a palm that grips wet or dusty surfaces. Hi-vis backs and reflective trim are optional but usually retained once a site tries them. Site work changes through the day, so most crews need two gloves rather than one. A thin PU or nitrile palm glove handles measuring, fixing and tool work where fingertips matter, and a heavier coated glove takes over for concrete, rebar and demolition, where cut and abrasion risk dominates. Buying both on one order keeps the cost per pair down and stops the expensive glove being destroyed on the wrong task. Tell us the trade mix on site and we will split the order to match it. ### Detail **Cut plus impact** An HPPE liner handles rebar and wire, while a TPR shell absorbs knuckle strikes. Combining them avoids the two-glove workaround that crews abandon. **Palm that survives concrete** Sandy nitrile or a reinforced synthetic leather palm resists concrete dust and wet grip far better than a bare knit. **Visible on site** Fluorescent backs and reflective knuckle trim make hand signals legible to plant operators in low light. ### Specification - Cut level: ANSI A4–A5 - Impact: TPR knuckle and finger guards - Palm: Sandy nitrile or reinforced synthetic leather - Visibility: Hi-vis back and reflective trim option - Sizes: US 7–11 - MOQ: 500 pairs per style and color - Packaging: 10 pairs per polybag, 100 pairs per carton - Lead time: Samples 7–10 days · bulk 20–30 days ### Site task to glove Level and TPR coverage follow the task, not the job title. Concrete finishing rarely needs the glove worn for rebar. | Task | Glove | Cut | Impact | | --- | --- | --- | --- | | Rebar / tying | A5 nitrile palm | A5 | Optional TPR | | Masonry / block | A4 sandy nitrile | A4 | Level 2 TPR | | Framing | A4 PU or nitrile palm | A4 | Level 1–2 TPR | | Concrete finishing | PVC or nitrile full dip | A1–A2 | None | | Traffic / plant | Hi-vis A4 | A4 | Level 2 TPR | ### Questions **What cut level do construction crews need?** A4 covers most site handling, A5 for rebar and heavy steel. Higher levels are warmer and stiffer, so specify the lowest level that covers the task. **Are impact gloves required on construction sites?** Requirements vary by employer and task. Where struck-hand risk is assessed, a TPR glove at level 1–2 is the usual starting point. **Can gloves be hi-vis and cut resistant?** Yes. Fluorescent knit and reflective trim can be added to an A4–A5 liner without affecting the cut level. **How do we handle size mix on site?** We pack S–XXL in the ratio you specify per carton, so sites receive the mix they actually use rather than surplus of one size. A flat carton is the usual reason a site runs out of medium while the large pile never moves. Confirm the ratio on the packing list before the first shipment. ### Related - Impact Resistant Gloves: https://workglovesfactory.com/impact-resistant-gloves/ - Cut Resistant Gloves: https://workglovesfactory.com/cut-resistant-gloves/ - Hi-Visibility Gloves: https://workglovesfactory.com/high-visibility-work-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## Mechanic Gloves URL: https://workglovesfactory.com/mechanic-gloves/ Section: Industries Primary topic: mechanic gloves Oil grip, knuckle protection and fingertips that still work a phone — built for technicians, not for a catalogue photo. ### Overview A mechanic glove has to do three things at once: hold oily tools, survive contact with hot and sharp components, and let the wearer use a phone or diagnostic tablet without taking it off. Most gloves do one of those well. We build mechanic gloves on a synthetic leather or sandy nitrile palm with a TPR knuckle shell, reinforced thumb and index, and conductive fingertips. The palm is thin enough to pick up a 10 mm bolt, and the back takes the knocks when a wrench slips. Automotive work punishes the palm and the knuckles at the same time. A nitrile palm holds oil and brake fluid reasonably well, but repeated contact with hot engine components and sharp edges wears a thin coating out in days. Foam nitrile on a seamless liner is the usual starting point, with a reinforced thumb crotch for pulling and a knit wrist that does not flap near rotating parts. Where impact tools are used, a back-of-hand guard is worth specifying — it is cheap, and it prevents the injury that takes a technician off the floor. ### Detail **Oil grip without slip** Sandy nitrile or textured synthetic leather holds oily tools. Smooth palms become dangerous the moment a fitting leaks. **Knuckle and thumb protection** A low-profile TPR shell on the knuckles plus reinforcement at the thumb and index — the two places technicians actually injure. **Phone-compatible fingertips** Conductive thumb and index let technicians check a diagnostic screen or take a photo without stripping the glove off with oily hands. ### Specification - Palm: Synthetic leather, sandy nitrile or PU - Back: Stretch knit with TPR knuckle guard - Fingertips: Touchscreen-compatible thumb and index - Cut level: A1–A3 depending on liner - Sizes: US 7–11 - MOQ: 500 pairs per style and color - Packaging: 10 pairs per polybag, 100 pairs per carton - Lead time: Samples 7–10 days · bulk 20–30 days ### Mechanic glove builds Specify a TPR shell wherever impact tools are used. Diagnostics and interior work are better served by the thin PU build. | Build | Oil grip | Impact | Typical use | | --- | --- | --- | --- | | Synthetic leather + TPR | High | Level 2 | General automotive repair | | Sandy nitrile + TPR | High | Level 2 | Heavy equipment, fleet | | Thin PU, no TPR | Medium | None | Diagnostics, interior work | | Leather palm, knit back | Medium | None | Welding-adjacent maintenance | ### Questions **Do mechanic gloves protect against oil?** They resist oil on the palm and keep grip, but they are not a barrier glove. For prolonged solvent or oil immersion, use a dedicated chemical-resistant glove. **Can I use a touchscreen with them on?** Yes, with conductive thumb and index fingertips. Confirm the device type when ordering, since the conductive yarn is matched to capacitive screens. **Are these gloves cut resistant?** Standard builds are A1–A2. For brake rotors, sharp sheet metal and glass, specify an A3–A4 liner; the glove becomes slightly warmer and stiffer. **Can we brand them for our workshop?** Yes. Logo print, woven label and custom cartons are available from 500 pairs per style and color. Embroidery is not usually the right route here, because the thread wears through at the knuckles long before the glove does. ### Related - Impact Resistant Gloves: https://workglovesfactory.com/impact-resistant-gloves/ - Grip Work Gloves: https://workglovesfactory.com/grip-work-gloves/ - Anti-Vibration Gloves: https://workglovesfactory.com/anti-vibration-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## Disposable Nitrile Gloves (Industrial Grade) URL: https://workglovesfactory.com/disposable-nitrile-gloves/ Section: Safety Gloves Primary topic: nitrile gloves Powder-free nitrile film for workshops, food handling and cleaning — industrial or food grade, in 3, 4 and 5 mil. ### Overview Disposable nitrile gloves are film gloves, not knitted work gloves. They are used for short tasks where the hand needs a clean barrier and full feel: food preparation, light maintenance, cleaning, hair and beauty, and handling small components that must not be contaminated. We supply industrial-grade and food-contact nitrile in 3, 4 and 5 mil, powder-free, in standard and extended cuffs. Thicker film resists tearing and punctures better but reduces feel; 4 mil is the usual compromise for workshop and food use. Specify by use, not by the word nitrile. Industrial-grade gloves are thicker and more tear resistant and suit grease, paint and general handling; food-contact gloves are made on a dedicated line and are the correct choice where the hand touches food directly. Neither is a medical or examination glove, and we do not supply those. Tell us the wall thickness you need, the cuff length, and whether powder-free matters for your task, and we will quote the right grade rather than the cheapest box. ### Detail **Grade matched to use** Industrial grade for workshops and cleaning; food-contact grade for kitchens and processing. Tell us the use and we quote the matching grade. **Thickness by task** 3 mil for feel and short tasks, 4 mil for general use, 5 mil for heavier handling and longer wear. Thicker is not always better if dexterity is the point. **Powder-free, low odor** Powder-free film avoids residue on parts and food. Nitrile also avoids the latex protein issue for users with latex sensitivity. ### Specification - Material: Nitrile butadiene rubber film - Thickness: 3 mil, 4 mil, 5 mil - Grade: Industrial or food-contact - Finish: Powder-free, textured fingertips - Sizes: S–XL - Packing: 100 gloves per box, 10 boxes per carton - MOQ: 10 cartons (10,000 gloves) per size and grade - Lead time: Stock 5–7 days · custom print 20–25 days ### Thickness selection This range is industrial and food-contact disposable nitrile. It is not a medical or examination glove and is not sold for clinical use. | Thickness | Feel | Durability | Typical use | | --- | --- | --- | --- | | 3 mil | Highest | Low | Food prep, short cleaning tasks | | 4 mil | High | Medium | Workshop, janitorial, laboratory | | 5 mil | Medium | High | Heavy cleaning, parts handling | ### Questions **Are these medical or examination gloves?** No. This range is industrial and food-contact disposable nitrile. It is not intended for medical examination, surgery or clinical use, and we do not supply it for those applications. **Nitrile or latex for food handling?** Nitrile avoids the latex protein issue and resists oils and fats better than vinyl. For food contact, specify the food-grade film and confirm the use with your own food-safety process. **Can disposable gloves be branded?** Yes. Box printing and custom cartons are available, typically from 10 cartons per size. The film itself is not printed. **How should they be stored?** Keep boxes closed, away from direct sunlight and heat. Nitrile film degrades with prolonged UV and ozone exposure, so rotate stock and use older cartons first. ### Related - Nitrile Coated Gloves: https://workglovesfactory.com/nitrile-coated-gloves/ - Safety Gloves: https://workglovesfactory.com/safety-gloves/ - Warehouse Gloves: https://workglovesfactory.com/warehouse-gloves/ - Contact: https://workglovesfactory.com/contact/ --- ## ESD & Anti-Static Gloves URL: https://workglovesfactory.com/esd-anti-static-gloves/ Section: Work Gloves Primary topic: esd gloves Carbon-infused knits and PU palms that bleed static without shedding lint — for PCB, electronics and clean assembly work. ### Overview ESD gloves exist because static damage is invisible until a board fails. They work by giving charge a controlled path to dissipate instead of building on the hand or the part. That makes surface resistance the specification that matters, not the word "anti-static" on the packaging. We build ESD gloves on carbon-infused nylon or polyester with a PU palm, targeting the 10⁶–10⁹ Ω range used in electronics assembly. Conductive fingertips are available for touchscreens, and the knit is designed to keep lint away from boards. Anti-static and dissipative are not the same thing, and the difference matters when you write the spec. A glove that bleeds static away slowly is not the same as one that controls the rate at which charge moves, and only the second belongs on a bench where a single spike damages a board. Tell us the resistance range your process specifies and whether the glove is laundered and re-measured between shifts, because a coating that washes out after ten cycles is not a saving. ### Detail **Resistance you can specify** We quote the surface resistance range rather than a vague anti-static claim, so your ESD coordinator has a number to check against the standard. **Low lint** Continuous-filament nylon and a PU palm shed far less fiber than cotton or staple yarns — important near exposed boards and optics. **Feel for small parts** Fine-gauge liners keep enough dexterity for SMT parts, connectors and cable work, which is where most handling time is spent. ### Specification - Surface resistance: 10⁶–10⁹ Ω (specified per style) - Liner: Carbon fiber conductive yarn, 13G, with nylon or polyester - Palm: PU fingertips and palm, carbon-loaded - Fingertips: Conductive fingertips for touchscreens - Sizes: S–L (XS–XL on request) - Size coding: Coloured cuff: pink S, green M, grey L - MOQ: 500 pairs per style and color - Packaging: 10 pairs per ESD bag or individual bag, 200 pairs per carton - Lead time: Samples 10–14 days · bulk 25–35 days ### ESD glove selection Gloves are one part of an ESD program. Wrist straps, flooring and packaging also determine whether a workstation is protected. | Build | Resistance | Lint | Typical use | | --- | --- | --- | --- | | Carbon nylon, PU palm | 10⁶–10⁸ Ω | Low | PCB assembly, test | | Carbon polyester, PU palm | 10⁷–10⁹ Ω | Low | General electronics | | Carbon knit, no coating | 10⁶–10⁹ Ω | Medium | Packing, warehouse ESD zones | | Carbon fiber, PU fingertips | 10⁶–10⁹ Ω | Low | Electronics, dust-free assembly, clean handling | | Standard PU (not ESD) | Insulating | Low | Not suitable for ESD areas | ### Questions **Are these gloves genuinely ESD-safe?** They are made with conductive carbon yarn to a specified resistance range. Confirm the range against your ESD program and check a sample with your own meter before adopting the style. **Can I use them on a touchscreen?** Conductive fingertips work with capacitive screens. Because the whole glove is mildly conductive, touch response is usually reliable. **Do ESD gloves need to be washed differently?** Wash cool without fabric softener, which coats the fibers and raises resistance. Air-dry; do not tumble dry on high heat. **What is the difference between anti-static and ESD?** Anti-static usually means the material resists charge build-up. ESD means it dissipates charge in a controlled way within a defined resistance range. For electronics work, specify the range. ### Related - PU Coated Gloves: https://workglovesfactory.com/pu-coated-gloves/ - Warehouse Gloves: https://workglovesfactory.com/warehouse-gloves/ - Safety Gloves: https://workglovesfactory.com/safety-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## HVAC & Plumbing Gloves URL: https://workglovesfactory.com/hvac-plumbing-gloves/ Section: Industries Primary topic: hvac gloves Fingertip feel for fittings and wiring, with just enough cut protection for sheet-metal duct edges. ### Overview HVAC and plumbing gloves have to handle a sequence of small, precise tasks: threading a fitting, stripping a wire, seating a connector, tightening a valve in a tight space. Bulky gloves slow all of it down, so technicians work bare-handed and get cut on duct edges instead. The right glove is thin at the fingertips and reinforced where sheet metal bites. A 15G or 18G liner with a PU or nitrile palm and A2–A3 cut protection covers most service work; a nitrile palm handles wet fittings without losing grip. HVAC, plumbing and electrical work share one problem: the glove has to be thin enough to start a screw and tough enough to survive sheet metal, pipe threads and insulation. A 15G or 18G nitrile palm glove with a short knit wrist is the usual answer, because it leaves the wrist free for a watch, a phone and a tool belt while covering the palm where the cuts happen. On copper and aluminium sheet, a cut level at the fingertips is worth the small loss in feel. For live electrical work, remember that a general glove is not insulating protection. ### Detail **Fingertip dexterity** Fine-gauge liners and form-fitting fingertips let technicians feel a thread engage — the main reason gloves get removed on service calls. **Duct-edge cut protection** A2–A3 HPPE at the fingertips and palm handles sheet-metal duct edges without adding bulk across the whole hand. **Wet grip** A nitrile palm holds wet pipe and fittings far better than leather, which hardens and slips when soaked. ### Specification - Liner: 15G nylon or 18G HPPE - Palm: PU or nitrile - Cut level: A2–A3 - Fingertips: Touchscreen-compatible option - Sizes: S–XL - MOQ: 500 pairs per style and color - Packaging: 10 pairs per polybag, 200 pairs per carton - Lead time: Samples 7–10 days · bulk 20–30 days ### Service task to glove Match the fingertip to the task: 18G for screws and duct edges, 15G nitrile for wet fittings, and no metal studs near a live panel. | Task | Glove | Cut | Note | | --- | --- | --- | --- | | Duct work | 18G HPPE, PU palm | A2–A3 | Thin fingertips for screws | | Pipe fitting | 15G nylon, nitrile palm | A1–A2 | Wet grip | | Electrical panel | 15G nylon, PU palm | A1 | No metal studs | | Refrigerant lines | Nitrile palm, fleece back | A1 | Cold lines plus grip | | Roof unit service | A3, touchscreen fingertips | A3 | Outdoor, phone use | ### Questions **Can these gloves be used for electrical work?** No. They are work gloves, not insulating gloves. Electrical protection requires a dedicated insulating glove rated for the voltage, with the correct class and testing regime. **What cut level do HVAC technicians need?** A2–A3 covers sheet-metal duct edges and most service handling. Thicker gloves reduce feel, so avoid jumping to A4 unless the task demands it. **Do they work with phones and tablets?** Yes with conductive fingertips. Service apps and diagnostics are a common reason technicians remove gloves, so this option usually pays for itself. **Are they warm enough for rooftop work?** Standard builds are not insulated. For cold rooftop service, specify a fleece-backed version with a nitrile palm. For wet roofs, keep the nitrile palm and skip the thicker liner, which only holds water against the skin. ### Related - Cut Resistant Gloves: https://workglovesfactory.com/cut-resistant-gloves/ - PU Coated Gloves: https://workglovesfactory.com/pu-coated-gloves/ - Mechanic Gloves: https://workglovesfactory.com/mechanic-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## High-Visibility Work Gloves URL: https://workglovesfactory.com/high-visibility-work-gloves/ Section: Work Gloves Primary topic: hi vis gloves Fluorescent backs and reflective trim so hand signals read at distance — in lime or orange, with cut and impact options. ### Overview Hi-vis work gloves exist because hand signals only work if they can be seen. In low light, rain or a busy yard, dark gloves disappear against machinery and clothing. Hi-vis gloves use fluorescent knit and reflective trim to keep hands legible to plant operators and drivers. The color is not cosmetic: fluorescent lime and orange are the background colors used in high-visibility clothing standards, and reflective trim adds return in headlights. We build them on the same liners as our standard gloves, so visibility does not cost cut protection. Hi-vis on a glove is a safety-system decision, not a colour choice. The value comes from being seen at distance in poor light, so the fluorescent colour needs to cover the back of the hand rather than a stripe, and reflective trim only helps when it faces a light source — which is why the usual layout puts a band across the knuckles and another along the cuff. In practice the glove also has to survive the work it is worn for, so we build hi-vis backs on the same abrasion-rated palms as the plain version rather than on a light-duty base. ### Detail **Seen at distance** Fluorescent knit backs plus reflective knuckle trim make hand signals readable in low light and headlights, where dark gloves vanish. **Protection unchanged** The hi-vis build uses the same HPPE or polyester liners as the standard range, so A2–A5 cut levels and TPR impact shells remain available. **Color by environment** Lime for general sites and daylight, orange for rail and where lime blends into vegetation. Both are available with reflective trim. ### Specification - Colors: Fluorescent lime, fluorescent orange - Trim: Reflective knuckle or cuff tape - Liner: 13G/15G polyester or HPPE - Cut level: A1–A5 depending on liner - Impact: TPR option - Sizes: S–XXL - MOQ: 500 pairs per style and color - Lead time: Samples 7–10 days · bulk 20–30 days ### Hi-vis builds Visibility does not replace the base glove. Choose the liner and cut level for the task first, then the colour. | Build | Cut | Impact | Typical use | | --- | --- | --- | --- | | Lime knit, PU palm | A1–A2 | None | Warehouse, yard, events | | Lime HPPE, nitrile palm | A4 | None | Road works, utilities | | Orange HPPE, TPR | A4–A5 | Level 2 | Rail, plant, heavy site | | Lime full-dip PVC | A1 | None | Wet outdoor work | ### Questions **Do hi-vis gloves meet a standard?** Work gloves are not certified as high-visibility garments. The colors follow the background colors used in high-visibility clothing standards, and reflective trim adds return. Treat them as a visibility aid alongside your hi-vis clothing. **Lime or orange?** Lime performs better in most daylight and urban backgrounds; orange is used on rail and where lime blends into foliage. Many buyers stock both and issue by site. **Does the color fade?** Fluorescent dyes fade with UV and industrial washing. Replace gloves when the color dulls, because faded fluorescence no longer performs its purpose. **Can hi-vis gloves include impact protection?** Yes. Reflective or fluorescent TPR shells are available on level 2 builds, combining visibility with struck-hand protection. Colour fastness matters as much as brightness: a lime back that fades in the wash stops being visible long before it wears out. ### Related - Construction Gloves: https://workglovesfactory.com/construction-gloves/ - Impact Resistant Gloves: https://workglovesfactory.com/impact-resistant-gloves/ - Cut Resistant Gloves: https://workglovesfactory.com/cut-resistant-gloves/ - Safety Gloves: https://workglovesfactory.com/safety-gloves/ --- ## Anti-Vibration Gloves URL: https://workglovesfactory.com/anti-vibration-gloves/ Section: Work Gloves Primary topic: anti vibration gloves Gel and foam palm systems that damp tool vibration — for grinders, breakers, compactors and saws. ### Overview Anti-vibration gloves address hand-arm vibration damage that accumulates over years, and they are only one control among several. A genuine anti-vibration glove uses a viscoelastic pad in the palm and fingers to attenuate vibration at specific frequencies, and is rated to EN ISO 10819 as TRM (medium) or TRH (high). Padding alone is not enough. The glove must also keep grip and dexterity, because a worker who cannot hold the tool safely will grip harder, which increases exposure. We build AV gloves on a knit or leather base with a gel palm and reinforced thumb. Vibration injuries build slowly, so the glove is only one part of the control. What a glove can do is damp the high-frequency component that reaches the hand and let the worker keep a relaxed grip, which is why the damping material sits between the palm and the tool rather than over the whole hand. Give us the tool, the trigger time and the shift length, and we will match a pad thickness. For long exposure, rotation and tool selection matter more than any glove. ### Detail **Rated attenuation** Gel or foam systems are specified to EN ISO 10819 TRM/TRH, so the damping claim has a test behind it rather than a padded palm. **Grip still works** A nitrile or leather palm over the gel keeps grip on handles and reduces the tendency to over-grip, which is a major part of vibration exposure. **Built for the tool** Full-finger gel for breakers and compactors, palm-only padding for grinders where fingertip feel matters, and a leather version for chainsaws. ### Specification - Standard: EN ISO 10819 (TRM / TRH) - Padding: Gel palm, foam palm, full-finger gel - Palm: Nitrile, leather or synthetic leather - Cut options: A2–A3 - Sizes: M–XXL - MOQ: 500 pairs per style and color - Packaging: 10 pairs per polybag, 100 pairs per carton - Lead time: Samples 10–14 days · bulk 25–35 days ### AV glove by tool Gloves reduce but do not eliminate vibration exposure. Tool selection, trigger time limits and job rotation remain the primary controls. | Tool | Build | Padding | Note | | --- | --- | --- | --- | | Angle grinder | Nitrile palm, knit back | Palm gel | Fingertip feel retained | | Road breaker | Leather palm, full gel | Full-finger gel | Heavy damping, lower feel | | Plate compactor | Leather or nitrile | Palm + finger gel | Grip on vibrating handle | | Chainsaw | Leather, left-hand protection | Palm gel | Check chainsaw-specific requirements | | Impact driver | Thin PU, no AV rating | None | Not an AV glove | ### Questions **Do anti-vibration gloves really work?** Rated gloves attenuate vibration at defined frequencies, but they are a secondary control. Reducing trigger time, using lower-vibration tools and rotating tasks matter more than the glove alone. **What do TRM and TRH mean?** EN ISO 10819 classifies vibration attenuation as medium (TRM) or high (TRH) based on measured transmission. Higher is not automatically better if it makes the glove too stiff to grip safely. **Can I use them for all-day work?** They are intended for vibrating-tool tasks, not all-day wear. Gel padding traps heat and reduces feel, so issue them for the specific task and pair them with exposure limits. **Are they cut resistant?** Some builds are A2–A3. If the task also involves sharp edges, specify the cut level alongside the vibration rating. ### Related - Impact Resistant Gloves: https://workglovesfactory.com/impact-resistant-gloves/ - Mechanic Gloves: https://workglovesfactory.com/mechanic-gloves/ - Construction Gloves: https://workglovesfactory.com/construction-gloves/ - Work Gloves: https://workglovesfactory.com/work-gloves/ --- ## Work Glove Size Chart URL: https://workglovesfactory.com/guides/glove-size-chart/ Section: Guides Primary topic: glove size chart Measure the palm, not the fingers: circumference and length in inches and centimeters, with fit notes for each glove family. ### Overview A work glove size chart is set by two measurements: the circumference around the palm just below the knuckles, and the length from the tip of the middle finger to the base of the hand. Sizing systems differ by market, so a US 9 is not automatically a European 9. Fit also changes with the glove family. A coated knit should be snug at the fingertips with no slack at the palm; leather should allow a little room for seam stretch; insulated gloves need space for the lining without the fingers bottoming out. ### Detail **Measure the dominant hand** Measure the hand you work with. Most people have a half-size difference between hands, and the working hand sets the size. **Circumference sets the size** The palm circumference is the primary number. Length confirms the fit, especially for long fingers or a short palm. **Family-specific fit** Coated gloves fit snug, leather fits with a little room, insulated gloves need clearance for the lining. Use the same chart but adjust for the build. ### Specification - Primary measure: Palm circumference below the knuckles - Secondary: Hand length, wrist to middle fingertip - Sizes: XS–2XL (US 6–11); one size on selected cotton styles - Units: Inches and centimeters - Fit: Snug for knit, room for leather, clearance for insulated - Custom grading: Available from 500 pairs per style ### Work glove size chart Measure the working hand. If between sizes, go up for insulated gloves and down for coated knit. | Size | US | Palm circumference | Hand length | | --- | --- | --- | --- | | XS | 6 | 6.0–6.5 in / 15–17 cm | 6.3–6.7 in / 16–17 cm | | S | 7 | 6.5–7.0 in / 17–18 cm | 6.7–7.1 in / 17–18 cm | | M | 8 | 7.0–7.5 in / 18–19 cm | 7.1–7.5 in / 18–19 cm | | L | 9 | 7.5–8.0 in / 19–20 cm | 7.5–7.9 in / 19–20 cm | | XL | 10 | 8.0–8.5 in / 20–22 cm | 7.9–8.3 in / 20–21 cm | | XXL | 11 | 8.5–9.0 in / 22–23 cm | 8.3–8.7 in / 21–22 cm | ### Fit by glove family Fit changes with the family: coated knit should be snug at the fingertip, leather needs room for seam stretch, and insulated gloves need space for the lining. | Family | Fit target | Common mistake | | --- | --- | --- | | Coated knit | Snug at fingertips, no palm slack | Sizing up for comfort, then losing feel | | Leather | Snug with slight room for seam stretch | Buying loose, which causes blisters | | Impact / TPR | Snug; the shell adds bulk | Sizing up twice | | Insulated | Room for lining, fingertips not tight | Buying the summer size | | Cut resistant | Snug; slack causes snagging | Buying loose for perceived protection | ### Cuff and overall length by family Cuff depth is measured from the cuff edge to the wrist crease; overall length runs from the cuff edge to the middle fingertip. Confirm the measurement point on the approved spec. | Family / cuff | Length (cm) | What it covers | | --- | --- | --- | | Short cuff / slip-on | 10 | Light handling with maximum wrist freedom | | Knit wrist | 18–21 | General handling; debris stays out of the cuff | | Standard knit or safety cuff | 22–24 | Sheet metal, glass and general industry | | Extended safety cuff | 25–27 | Forearm splash and scrap | | Gauntlet | 30–33 | Welding, furnace and wet washdown | ### Questions **How do I measure my hand for gloves?** Wrap a tape around the palm just below the knuckles, keeping it flat. Then measure from the wrist crease to the tip of the middle finger. Use the circumference to pick the size and the length to confirm it. **What if I am between sizes?** For coated knit and cut gloves, size down for a snug fit. For insulated and impact gloves, size up to leave room for the lining and shell. **Are US and EU glove sizes the same?** No. US sizes are typically 6–11; European sizes often use 6–11 as well but the measurements behind them differ. Always check the circumference, not the number alone. **Can you produce a custom size grading?** Yes, from 500 pairs per style. Send your size ratio and measurements; we adjust the pattern and confirm on a sample before bulk. **What glove length do I need?** Match length to exposure. A 10 cm cuff is enough for light handling, 18–21 cm knit wrists cover general work, 22–24 cm is the common safety cuff for sheet metal and glass, and 30–33 cm gauntlets are for welding, furnace and washdown work. ### Related - Work Gloves: https://workglovesfactory.com/work-gloves/ - Types of Work Gloves: https://workglovesfactory.com/guides/types-of-work-gloves/ - Custom Work Gloves: https://workglovesfactory.com/custom-work-gloves/ - Contact: https://workglovesfactory.com/contact/ --- ## Types of Work Gloves, Explained URL: https://workglovesfactory.com/guides/types-of-work-gloves/ Section: Guides Primary topic: types of gloves A working taxonomy: what each glove family is for, what it is not for, and how to narrow the choice in three questions. ### Overview Types of work gloves are usually organized by material, which is not how work is organized. A buyer scanning "nitrile, PU, latex, PVC" has to translate chemistry into a task before the page makes sense. This guide inverts that: start from the hazard and the environment, then land on the family. There are eight families worth knowing for general industry. Everything else is a variation on liner, coating, cuff and level. Once you can place a task in one of the eight, the remaining choices are about fit, rating and packaging. ### Detail **Three questions** What can cut or hit the hand, what is on the surface, and how wet or hot is the environment. Those three answers eliminate most of the catalogue. **Families, not brands** Each family is defined by construction — liner plus coating plus cuff — not by a brand name. That makes comparisons between suppliers possible. **Limits stated** Every family has a job it cannot do: coated knit is not chemical protection, leather is not cut-rated by default, disposable nitrile is not a work glove. ### Specification - Families: 8 core families for general industry - Selection basis: Hazard, surface, environment - Ratings: ANSI/ISEA 105, ANSI/ISEA 138, EN388 - Common coatings: PU, nitrile, PVC - Common liners: Polyester, nylon, HPPE, cotton, leather - MOQ: 500 pairs per style and color ### Core work glove types The eight families are a starting point, not a catalogue. Most orders are a variation on one family’s liner, coating, cuff and rating. | Type | Built from | Best for | Not for | | --- | --- | --- | --- | | Coated knit | Knit liner + PU/nitrile/PVC palm | Handling, assembly, general work | Heat, chemical permeation | | Cut resistant | HPPE / glass / steel liner | Sharp edges, sheet metal | Needle sticks | | Puncture resistant | Dense liner + reinforced palm | Wire, glass, scrap | Needle-proof claims | | Impact resistant | TPR shell over knit or leather | Struck hand, construction | Heat or chemical | | Leather | Cowhide, goatskin, pigskin | Abrasion, sparks, rigging | Wet grip, cut rating by default | | Insulated | Fleece/acrylic lining + coated palm | Cold work, cold storage | Hot work | | Waterproof | Full nitrile/PVC shell | Wet handling, washdown | Chemical protection | | Disposable | Nitrile or vinyl film | Food, cleaning, light barrier | Reusable handling work | ### Questions **What is the most common work glove?** The palm-coated knit glove, usually PU or nitrile. It covers the widest range of handling tasks at a cost that allows frequent replacement. **Are leather gloves cut resistant?** Leather resists abrasion well but is not rated for cut unless it is combined with a cut-resistant liner. Do not assume leather means cut protection. **When should I use disposable gloves instead of work gloves?** When the priority is a clean barrier for a short task — food handling, light cleaning, small parts — rather than abrasion or impact protection. Disposable film tears quickly under real work loads. **How many types should a site stock?** Most sites need three to five: a light handling glove, a cut glove, a wet or oil glove, a cold glove and a heavy-duty leather. More than that usually means the wrong gloves are being issued. Start with the glove people actually keep on, then add the specialists around it. ### Related - Work Gloves: https://workglovesfactory.com/work-gloves/ - ANSI Cut Levels: https://workglovesfactory.com/guides/ansi-cut-levels/ - Glove Size Chart: https://workglovesfactory.com/guides/glove-size-chart/ - Safety Gloves: https://workglovesfactory.com/safety-gloves/ ---